Adler AD 7323 Bedienungsanweisung Seite 4

injury or damage to the device.
DETAILED SAFETY INSTRUCTIONS
1.Use only original assembly parts, which were supplied with the fan set.
2.The device may be turned on only after it is fully assembled. A partially assembled and started-up device does not guarantee safe use
and proper operation.
CAUTION: DO NOT TURN THE FAN ON WITHOUT ATTACHING THE FRONT AND REAR GUARDS.
3.Place the fan away from curtains, sheer curtains and other items, which can be sucked in by the running fan.
4.Do not insert any objects into the fan guard. This could hurt your body or damage the device.
DESCRIPTION OF THE DEVICE: STAND FAN Ad7323
1. Front guard
4. Rear guard nut
7. Motor head lock
10. Control panel housing
13. Height adjustment
16. Round base
FAN ASSEMBLY
1.Make sure that the power cord is disconnected from the electrical socket.
- Assemble the fan base (15, 16) and attach the exterior barrel (14). Under the round base fix the base stability part (17) and use plastic
nipple (18) to tighten the round base (16).
- Attach the exterior barrel (14) to the control panel housing (10) using the mounting screw (11).
2. Attach the rear guard (5) to the motor unit (6) using the nut (4).
3. Place the fan blade (3) on rotor axis. Fasten with the blade nut (2) in counterclockwise direction. Check to make sure that the blade
rotates without resistance.
4. Position the front guard (1) opposite the rear guard (5) push the guard retaining clips into position ensuring that they engage correctly
on the rim of the guard. Pass through the hole of the front guard and rear guard with a small screw, then tighten it with a nut.
USING THE DEVICE
1. Press the '0' button on the control panel (9), then plug the power cord into an electrical socket.
2. Turn the fan on by pressing:
- button '1' to rotate fan blades at slow speed, or
- button '2' to rotate fan blades at medium speed, or
- button '3' to rotate fan blades at the maximum speed.
3. To turn on the left and right direction oscillating motion of the fan unit please do press the motor head lock button (7) down. Pulling the
button (7) upwards will turn the oscillation off.
4. You can adjust the fan's vertical angle by tilting the motor unit (6).
CLEANING AND MAINTENANCE
CAUTION: Do not allow the fan's motor part or any buttons to get wet.
1. Before cleaning remove the plug from the electrical socket.
2. To clean dust from the fan blades, remove the front guard. Remove the fan blade from the rotor axis, wipe with a damp cloth, then
wipe dry.
3. To clean the motor unit gently wipe it with a damp cloth, without detergents. Wipe dry.
4. Store the fan in a dry place.
TECHNICAL INFORMATION:
Diameter 40cm / 16"
Power supply 220-240V ~ 50/60Hz
To protect your environment: please separate carton boxes and plastic bags and dispose them in corresponding waste
bins. Used appliance should be delivered to the dedicated collecting points due to hazarsous components, which may
effect the environment. Do not dispose this appliance in the common waste bin.
ALLGEMEINE SICHERHEITSVORSCHRIFTEN LESEN SIE AUFMERKSAM WICHTIGE
ANWEISUNGEN BEZÜGLICH DER SICHERHEIT DER BENUTZUNG BEWAHREN SIE
Bei Verwendung des Gerätes zu gewerblichen Zwecken werden die Garantiebedingungen
geändert.
1.Vor dem ersten Gebrauch, die Bedienungsanleitung lesen und die dort angegebenen
Hinweise beachten. Der Produzent trägt keine Verantwortung für Schäden, die aufgrund
von bestimmungswidriger Nutzung oder unsachgemäßer Bedienung entstanden sind.
2.Das Gerät ist nur für den Hausgebrauch verwendet. Verwenden Sie es nicht für andere
Zwecke als den bestimmungsgemäßen Gebrauch.
3.Das Gerät ausschließlich an die Steckdose 220-240 V ~ 50/60 Hz anschließen. Es darf
nicht zu anderen, bestimmungswidrigen Zwecken benutzt werden. Wegen
2.Blade nut
5.Rear guard
8.Power cord
11.Mounting screw
14.Exterior barrel
17. Base stability part
Power: 45W
Noise level 53 Db
DEUTSCH
DIESE FÜR DIE ZUKUNFT AUF
3.Blade
6.Motor unit
9.Control panel
12.Interior barrel
15.Base guard
18. Plastic nipple
Max Power: 90W
4