C-Control GX107 Bedienungsanleitung Seite 2

Operating instructions
Remote control module GX107
Item no. 1629152
Intended use
The product is intended to provide the "GX107" (Item no. 1629146) with a GPS function; the
product must only be used with this model.
Further information on its use can be found in the manual for the main device "GX107". If this
GPS module is listed as an accessory for another model in the GX series, the device in ques-
tion is automatically included in the intended use.
No part of the product may be modified or rebuilt!
Any use other than described above is not permitted and can damage the product. Further-
more, there are dangers such as fire, short circuit, electric shock etc..
The product complies with the applicable National and European regulations. All names of
companies and products are the trademarks of the respective owner. All rights reserved.
The safety instructions are to be observed without fail!
Package contents
• GPS module for "GX107"
• 1 Hook-and-loop tape
• Operating instructions
Up-to-date operating instructions
Download the latest operating instructions via the link www.conrad.com/downloads or scan the
QR code. Follow the instructions on the website.
Safety instructions
The warranty will be void in the event of damage caused by failure to observe
these safety instructions! We do not assume any liability for any consequen-
tial damage!
Nor do we assume any liability for material and personal damage caused by
improper use or non-compliance with the safety instructions! The warranty
will be void in such cases.
• The product is not a toy and should be kept out of the reach of children.
• The unauthorised conversion and/or modification of the product is inadmissible
because of safety and approval reasons.
• The product is protected according to IP66, the GPS module is intended for use in
unprotected outdoor areas. Do not use the GPS module in or under water.
• Do not leave packaging material lying around carelessly. It may become danger-
ous playing material for children.
• Please consult the operating instructions for the "GX107". These contain further
information on the use of the GPS module.
Connecting to the "GX107"
• Before making the connection, please remove the power supply and the rechargeable battery
from the main device "GX107".
• Please consult the operating instructions for the "GX107" to ensure that you connect the GPS
receiver to the intended jack.
• The plug for the GPS module and the jack on the "GX107" have reverse voltage protection.
Do not use force when connecting the GPS module to the "GX107".
• It only requires a normal reset to make the GPS module ready for use (no power supply or
reset button).
Attaching the GPS module
• To attach the GPS module, an inbuilt magnet and a hook-and-loop tape are provided.
• In the case of attachment to metal surfaces by means of the magnet, it is recommended
that additional fixing be used, e.g. cable straps. This applies especially for use with moving
objects.
• For attachment to other surfaces, the hook-and-loop tape provided strip can be used.
• Please observe the correct orientation of the receiver. The GPS label on the GPS module
casing must be in the line of sight with the GPS satellite.
The more free space over the GPS module, the more GPS satellites can be received. This
enhances the accuracy.
Normally, GPS reception inside buildings is not possible. Try to position the GPS module near
a window (however, this must not be metallised insulated glass, this blocks reception). The
cable can be positioned outside. However, please make sure that it does not get squeezed
and damaged.
GPS reception can be expected to be further impaired in the vicinity of buildings, mountains,
trees/forests etc.
When used in vehicles, the GPS module should be placed near a window; however, wires in
front and rear windscreen heating may impair proper reception.
Disposal
Dispose of the product at the end of its serviceable life in accordance with the cur-
rent statutory requirements; e. g. return it to any suitable collection point.
Declaration of conformity (DOC)
We, Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau, hereby declare that this
product conforms to the 2014/53/EU directive.
The full text of the EU conformity declaration is available via the following Internet
address:
www.conrad.com/downloads
Select a language by clicking a flag symbol and enter the order number of the prod-
uct in the search field; then you will be able to download the EU declaration of
conformity in PDF format.
Technical data
Protection class ............................ IP66
Dimensions (L x W x H) ................ 37 x 34 x 14 mm (without cable)
Cable length ................................. approx. 300 cm
Weight .......................................... approx. 80 g
Operating temperature range ....... -40 °C to +85 °C
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
© Copyright 2018 by Conrad Electronic SE. 1629152_V1_0118_01_VTP_m_en