Getting Started - savic Dog Park de luxe Montage

EN
1 2a
A
panel A
Feld A
corner Tube
B G H I
3
C
D
E
F
Introduction
Please read these instructions fully before you begin to
assemble your Dog Park de luxe. You should have the
following components:
A) 1x Dog Park de luxe
B) 1x Top underside hinge adaptor
C) 2x Bottom hinge adaptor
D) 2x Top cap
E) 1x Bottom cap
F) 2x Top topside hinge adaptor
G) 2x Wall bracket covers
H) 2x Wall brackets
10x Screws and wall plugs
I) 7x Corner Tubes (1)

Getting started

You should assemble your Dog Park de luxe on a level
and stable surface. Unfold the dog pen and set to the
desired confi guration. For a hexagonal dog pen set
each panel to a 60º angle between adjacent panels.
Align the open ends of the dog pen and insert them into
each other, panel B fits into panel A. Insert the Corner
Tube (Part I) into the top hole of panel A, compress the
spring in the top hole so the Corner Tube can slide into
2b
panel B
Feld B
Eckrohr
4
button gate handle
Gri
Knopf
the base hole of panel B. (2A+2B)
To complete your dog pen, turn the hinges
at the base of the barrier to the closed lock position to
fix their position. Your dog cushion can now be placed
into the dog pen and secured to the bottom bars of
each panel with the ties.
To Open Gate
Using one hand, place your thumb on the button and
grip the gate with your fi ngers. Slide the button and
lift the gate, then open the gate in either direction,
when released the gate will swing closed automatically.
Always check the gate is closed properly. (3)
Using your Dog Park as a hearth
guard or stair guard
Up to 6 panels of your Dog Park may be used in open
confi gurations providing the 2 end panels are securely
fixed to a wall with the fixings provided. (4)
5
A
B
geschlossen locked
8
G
Fixing your Dog Park on stairs
If the product is used at the top of the stairs: in order
to prevent a dog climbing downstairs, it should not be
postioned below the top step. (See picture A). It should
be postioned on the top level. (See picture B).
If the product is used at the bottom of the stairs: in
order to prevent a dog climbing upstairs, it should be
positioned on the lowest step. (See picture C). (5)
Note A:
To Remove Unwanted Panels
Turn the base knob anti-clockwise to the unlocked
position; pull up the corner tube to compress the spring
in the top hole making it easy to slide the bottom of
the corner tube out from the base. With the corner tube
removed you can lift and remove the unwanted panel. (6)
First assemble the barrier adaptor hinges for each end,
slide (C) over the Corner Tube and insert into (B) or (F),
then compress the spring in the top hole and slide the
base of the Corner Tube into position above (E) or into
(D). (7)
Place wall bracket (H) over covers (G), clip cover (G) to
hinges (F) and (C) or (B) and (C) ensuring the small silver
studs on the adaptors are positively engaged in cover
(G). (8)
6
panel A panel B
Feld a Feld b
C
corner Tube Eckrohr
9a
H
C
Note B:
To remove the barrier panels from the wall
fi xings use a pen to push the top and bottom studs in,
then pull the barrier away from the wall evenly.
Place the assembled barrier against the wall to
determine the fi xing positions (mark the centre position
on your wall with a pencil). Now remove the wall bracket
from the wall cover, hold your wall bracket upright
against the wall in the marked location, and mark the
centre of each slot.
Select the appropriate fi xing method from the following
list. This barrier must only be fi xed to a solid and secure
surface. (9A+9B)
EN
7
G
G
H F H
B
C
C
E D
9b