Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Operating instructions
3.5" IDE for SATA hard disk converter
Item no. 1628715
Intended use
This product is intended for installation into a PC-compatible computer and serves to connect an IDE device
(e.g. IDE hard drive, IDE CR-ROM/DVD-ROM etc.) to a SATA interface of a SATA controller.
It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in bathrooms, must be
avoided under all circumstances.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use the product
for purposes other than those described above, the product may be damaged. In addition, improper use can
cause hazards such as short circuiting, fire, electric shock etc. Read the instructions carefully and keep them.
Make this product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All company names and
product names are trademarks of their respective owners. All rights reserved.
Delivery content
• Converter board
• Operating instructions
Latest operating instructions
Download the latest operating instructions via the link www.conrad.com/downloads or scan the QR code
shown. Follow the instructions on the website.
Explanation of symbols
The lightning symbol inside a triangle is used when there is a potential risk of personal injury,
such as electric shock.
An exclamation mark in a triangle indicates important instructions in this operating manual that
absolutely have to be observed.
The arrow symbol indicates specific tips and advice on operation.
Safety instructions
Read the operating instructions carefully and especially observe the safety information.
If you do not follow the safety instructions and information on proper handling in this
manual, we assume no liability for any resulting personal injury or damage to property.
Such cases will invalidate the warranty/guarantee.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become dangerous playing
material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity,
moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and protect it
from any accidental use. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage
the product.
• Also observe the safety and operating instructions of any other devices which are connected
to the product.
• If you do not have the necessary expertise for installation, let an EXPERT or a corresponding
workshop carry out the installation. Improper installation will damage the board as well as your
computer and all connected appliances.
• Careful, Mortal Danger! Turn off the computer into which you want to install the card as well as
all other connected appliances and pull the power plug on all appliances! Merely turning the
computer off via the on/off switch is not sufficient!
• Consult an expert when in doubt about operation, safety or connection of the device.
• Maintenance, modifications and repairs are to be performed exclusively by an expert or at a
qualified shop.
• If you have questions which remain unanswered by these operating instructions, contact our
technical support service or other technical personnel.
Operating controls
+
A
B
J2
A
SATA connection, connected via SATA cable with a SATA port of the controller or mainboard
B
LED connection (+ is the positive LED connection)
C
4-pole 3.5" power connection, connect with PC power supply
D
40-pole female connector strip, connect with IDE device (one "hole" above the female connector strip
is closed. This normally prevents the wrong attachment of the strip)
J2
This jumper (plugged in on delivery) must be removed when experiencing problems operating
CD/DVD/ATAPI drives.
Installation
If you do not have the necessary expertise for installation, let an EXPERT or a corresponding
workshop carry out the installation. Improper installation will damage the board as well as your
computer and all connected appliances.
Careful, Mortal Danger! Turn off the computer into which you want to install the card as well as
all other connected appliances and pull the power plug on all appliances! Merely turning the
computer off via the on/off switch is not sufficient!
• Open the housing of your computer and carefully remove the cover.
• Connect the board with a 40-pole IDE interface of an IDE device. Observe the proper connection and make
sure that the board is not shifted by one pin. One "hole" above the female connector strip is closed. This
normally prevents the wrong attachment of the strip. See the illustration above for the correct attachment!
Never attach the adapter board to the 40-pole connector of an IDE controller (of the mainboard
or the PCI controller)! Only connect the 40-pole female socket strip with the corresponding plug
of an IDE device, e.g. an IDE hard drive.
• Connect the SATA connection on the board via a suitable cable with a port of the SATA controller. The
SATA plugs have an anti-twist protection and only fit in one position.
• Connect the power socket on the circuit board of the miniature converter and the power socket of the IDE
device with the power pack unit of your PC.
• Close the casing of your computer.
• Connect your computer and the monitor to the power supply and turn all devices on.
• If your computer does not start properly, turn it off immediately and check all settings and cable connections.
Prior to opening the PC again, disconnect it from the power supply again (see above)!
Driver Installation
As the converter only adapts the two interface models to each other, it is not necessary to install a driver.
There is no driver disk or CD enclosed! The SATA controller treats the IDE device connected to the miniature
converter just like a common device with SATA interface.
Tips & notes
• If you connect a reformatted "new" hard disk to the converter, you must partition and format the hard drive
prior to using it.
• The miniature converter also allows you to operate CD/DVD-ROM drives, CD/DVD burners etc. on the
SATA interface. Please also consult the operating instructions of your SATA controller (on the mainboard
or PCI Plug & Play board) to see whether this is supported. Some SATA controllers only allow IDE hard
drives and no other IDE devices!
• If you experience problems while operating CD/DVD/ATAPI drives (e.g. device is not detected, read/write
problems or similar), remove the jumper "J2" from the circuit board.
• Make sure that you connect both the miniature converter as well as the IDE device with the PC power
supply.
• In case the LED connected to the LED connector does not light up upon access of the IDE device, pull the
LED plug and plug it in after turning it by 180°.
• When attaching the miniature converter to the IDE device, make sure you do not shift it by a pin.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the household waste. At
the end of its service life, dispose of the product according to the relevant statutory regulations.
You thus fulfil your statutory obligations and contribute to the protection of the environment.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the
capture in electronic data processing systems require the prior written approval by the editor. Reprinting, also in
part, is prohibited. This publication represent the technical status at the time of printing.
Copyright 2018 by Conrad Electronic SE.
HDD...
C
D
*1628715_V1_0218_02_mxs_m_en
Werbung
