Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Version 10/09
Operation Instructions
SAT finder
Item-No. 1404330
This product complies with the applicable national and
European specifications.
Intended use
The SAT finder enables to find new satellites and align satellite
dishes . If the device is used for other purposes, no warranty is
given!
The SAT Finder is only approved for connection to standard
satellite components (SAT antenna, receiver, multi-switch).
Any other use than the one described above leads to damage to
the pro-duct and is additionally tied to risks.
Safety advice
·
The guarantee will lapse if damage is incurred as a result of non-
compliance with the operating instructions. We will not assume any
responsibility for any consequential damage. We do not accept any
liability for personal injury or damage to pro-perty caused by incorrect
handling or failure to observe the safety instructions.The warranty will
be endered null and void in such cases.
·
For safety and licensing (CE) reasons, unauthorised conversion and/or
modifications to the product are not permitted.
·
The product may not be subjected to extreme temperatures, strong
vibrations, heavy mechanical strain, direct sunlight or high degrees of
humidity.The product may become damaged.
·
The device is not a toy and should be kept out of the reach of children.
·
Do not leave packaging material lying around carelessly.This could
become a dangerous toy in the hands of children.
·
Do not put the product into operation if it is damaged.
·
The manufacturer or supplier will assume no resonsibility for incorrect
displays or the consequences which arise through an incorrect display.
·
Do not use the product in situations in which professional measuring
technology is required.
·
Avoid using the device under unfavourable ambient conditions.
·
Contact with moisture must be avoided at all times.
·
The device may never be operated unsupervised.
·
If questions arise which are not clarified within the course of these
operating instructions, please contact our technical support or another
specialist.
In commercial institutions, the accident prevention regulations of the
·
Employer's Liability Insurance Associations for Electrical Systems and
Operating Materials are to be observed.
·
Numerous regulations have to be observed when
assembling/installing satellite systems (e.g. safety, lightning protection
etc.).Therefore, a satellite system should always be installed and
serviced by a professional technician familiar with the respective risks
and regulations.
The installation and servicing of satellite systems also requires
·
knowledge of the accident prevention regulations. When installing or
servicing satellite systems, ensure a safe stand and sufficient weight-
bearing capacity of ladders and similar equipment (have this secured
by a second person, if applicable). When working on satellite systems,
wear slip-proof shoes and suitable clothing. It may be necessary to
secure the installation site (e.g. wear safety belts). In the interests of
your own safety, you must always comply with the safety instructions.
·
Also observe the safety and operating instructions of any other
devices that are connected to this device.
Connection of the SAT Finder and
Alignment of the satellite antenna
To prevent short circuits, separate any multiswitches and the satellite
receiver from their power supply before connecting (pull the power
plug). Avoid short-circuiting or overloading the connected F connection
cable or the SAT Finder input „LNB" , otherwise the SAT Finder or the
connected receiver may be damaged.
!
Connect the output of the LNB with the connection „LNB" of the SAT
Finder.
!
Connect the connection „REC" of the SAT Finder with the antenna
input of the satellite receiver (often marked with „IF INPUT").
!
Check the correct connection. Plug the mains plug of the SAT receiver
into a wall outlet and turn the receiver on.
!
Adjust Satellite antenna roughly
!
When LED-chain lights up in full (1), turn gain control (2) anti-clockwise
until 2-3 LEDs light-up
!
now you may fine-adjust the Satellite antenna until you see the max.
red illuminating LEDs.
!
The higher the level on the SAT finder input, the higher the signal of
the acoustic level indicator.
!
Once the satellite antenna is optimally set, fix it in place (observe the
manufacturer's instructions).
!
Pull the mains plug of the satellite receiver and remove the SAT finder
from the antenna cable.
!
Connect the LNB with the satellite receiver or restore the original
cabling.
!
Check the picture on theTV and whether the right satellite is accessed.
You may have to repeat the setup procedure.
Checking the 22kHz conversion signal:
!
The LED "22kHz ein" lights up (3) as soon as a 22kHz signal is carried
forward.
ƒ
Technical Data
Frequency range
Through loss
Operating voltage
Current consumption
with LED display, acoustic signal, 22 kHz LED
These operating instructions are published by Conrad Electronic SE,
Klaus-Conrad-Straße 1, D-92240 Hirschau/Germany.
The operating instructions reflect the current technical specifications at time of
print. We reserve the right to change the technical or physical specifications.
© Copyright 2009 by Conrad Electronic SE. Printed in Germany.
‚
950...2400 Mhz
<10 dB
13...18 VDC
max. 120 mA
Werbung
