Before You Start; Getting Started; Charging Battery; Network Setup - Audizio VENICE Schnellstartanleitung

BEFORE YOU START

Please ensure the following is ready:
You have a broadband internet connection. A wireless broadband router is connected to the internet successfully. The radio
supports Wireless B, G and N connection (Wireless N router can also be used with the setting on B or G). You know the Wired
Equivalent Privacy (WEP) or Wi-Fi Protected Access (WPA) data encryption code/password. You need to key in the correct
code when the radio is connected to the wireless router for network connection. If you do not know the code/password,
please contact the person/technician who set up the router/network for you. The radio can work via Wireless network
connection (Wi-Fi connection).

GETTING STARTED

The radio is powered by the built-in lithium battery. A USB cable is supplied in the product package. Press and hold the [ ]
button to power on. To power off the radio, press and hold the same button. The Standby mode is enabled only when the
power is connected and so to make use of the Alarm clock function. Connect the power supply to the radio, press and hold
the [ ] button to turn it on. Pressing the [ ] button again will put the radio into standby.

CHARGING BATTERY

You can check the level of battery power remains on the radio. There is a battery power indicator
of the screen. When battery power is low, the battery indicator keeps blinking as a reminder for battery charging. To charge
the battery, connect the micro USB plug to the port where located at the rear side of the radio, connect the other end to a
power source supplied in 5V OUT (the rating of the electric current is minimum 1A or higher). The LED on the rear side of the
radio will light up in red indicates the battery is charging. The charging icon
When charging is done, the LED on the rear side will turn to green and the icon on screen will change to . It means the radio
has the power connected.
Note: The charging might take much longer to complete if the radio is playing while charging.

NETWORK SETUP

Internet connection can be setup via Wireless network (WiFi). Your radio requires a broadband Internet connection.
•
If this is first time use, the Configure Network wizard will be displayed. Choose Yes to start configuring network.
Press the [◄] button to highlight Yes and press [Dial/Select] to confirm.
Select Add/Remove AP from the list, use the [Dial/Select] knob to scroll and press it to confirm, then choose Add AP (Scan).
•
It will start scanning the Wi-Fi networks available. Scroll to your network and press [OK] to confirm. If your wifi
network has a password protected, it will ask you to enter the passphrase/password.
Note: The password is case sensitive. Please consult with the one who setup your network if you don't know the password.
•
When the Wi-Fi connection is successful, the Association Complete will be shown briefly. The wifi signal bar will
appear on the top left corner of the display.
BT PLAYBACK
Before transmission between your BT device and the radio is possible, both devices must be coupled. This process is called
"pairing". The radio is served as a receiver, to receive music stream to play on the radio.
If you have already coupled to a BT device before, this connection will be restored automatically when both devices are in
range and BT operation has been selected on the radio. "Pairing" does not have to be repeated. This function
may need to be activated in your BT device, however.
•
Push the Menu button to display the selection menu for the different operating modes.
•
Use the up/down button to select the operating mode BT and push the dial switch.
•
Switch your BT device to which you want to connect the radio on and activate the pairing mode here. The device
scans for BT devices in the reception range.
•
When the radio is found, your BT device shows its name Audizio Venice-XXXX (the XXXX is an identification code for
your radio unit).
•
Select the radio at your BT device.
•
Start playback on your BT device.
•
Playback now takes place using the radio.
QUICK START GUIDE
showing on the top row
will appear on the screen.