Renkforce 1295744 Bedienungsanleitung Seite 2

Operating instructions
6.35 cm (2.5") SATA HDD/SSD
PC front plug-in unit
Item no. 1295744
Intended use
The product is designed for installation in an empty 8.9 cm (3.5") drive bay of a computer
case. The product features a plug-in slot for one 6.35 cm (2.5") SATA HDD/SSD. Power
is supplied via a PC power supply unit.
For safety and approval purposes (CE), you must not rebuild and/or modify this product.
If you use the product for purposes other than those described above, the product may
be damaged. In addition, improper use can cause hazards such as short circuiting,
fire, electric shock etc. Read the instructions carefully and keep them. Make this
product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All
company names and product names are trademarks of their respective owners. All
rights reserved.
Delivery content
• PC front plug-in unit
• 4 x screws
• Operating instructions
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the
warranty/guarantee.
• Electrostatic charges may damage electronic components. Do not touch
electronic components with your bare hands.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may
become dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong
jolts, high humidity, moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of
operation and protect it from any accidental use. Safe operation can no
longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a
low height can damage the product.
• Also observe the safety and operating instructions of any other devices
which are connected to the product.
• Consult an expert when in doubt about operation, safety or connection of
the device.
• Maintenance, modifications and repairs are to be performed exclusively
by an expert or at a qualified shop.
• If you have questions which remain unanswered by these operating
instructions, contact our technical support service or other technical
personnel.
Installation and operation
If you do not have thorough knowledge on the installation of this product,
have the installation carried out by a professional or in a specialist shop!
Incorrect installation of the product will cause damage to the product, your
computer and all connected devices.
Caution, risk of fatal injury!
Turn off the computer in which you wish to install the product, and all
connected devices. Disconnect all devices from the power supply by
unplugging them. Simply turning off the devices using the on/off switch
does not mean a device is voltage-free!
• Open your computer's case and remove the lid carefully.
• Locate a free 8.9 cm (3.5") drive bay and remove its front panel. There may be a
metal cover in place behind the panel that needs to be removed. In some cases,
these covers can be unscrewed; in others they should be carefully pried out.
Depending on the case, the entire front cover may need to be removed in advance
to complete this step.
• Push the product into the slot of the computer casing, observing the right direction.
The power LED must be located on the left side.
• Attach the product with the provided screws to the casing.
• Connect the SATA cable to the matching connector of the mainboard. Make sure
the polarity of the connection is correct and do not exert any force. Follow the
instructions provided in the mainboard manufacturer's manual.
• Connect the power cable to the PC power supply unit.
• If necessary, secure the cables with cable ties in order for them not to reach into
the fans of your computer.
• Reclose your computer's case.
• Connect one 6.35 cm (2.5") SATA HDD/SSD to the respective terminal block inside
the product. Do not use any force.
• Connect your computer and monitor to the power supply and turn on all devices.
• Once the product is ready for use, the power LED lights up.
• If your computer does not start up normally, turn it off immediately and check all
settings and cable connections.
Before reopening your computer, disconnect it from the power supply; see
above!
Tips and notes
• The required drivers are already included in the operating system. For that reason
the delivery does not include any separate storage medium.
• The product supports both plug & play and hot swapping.
The inserted HDD/SSD can be removed whilst the operating system is running. But
you should wait until all reading/writing operations are completed and securely
disconnect the HDD/SSD through the operating system. The data on the HDD/SSD
could get damaged otherwise. It might even be necessary to format the HDD/SSD
afterwards.
• Windows® XP does not support hard drives with a capacity of >2 TB.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the
household waste.
At the end of its service life, dispose of the product according to the
relevant statutory regulations.
You thus fulfil your statutory obligations and contribute to the protection of
the environment.
Technical data
System requirements .................................... W indows® XP (Home, Pro, with SP1, SP2,
Interface ..........................................................SATA III
Supported HDD/SSD installation height ....5/7/9.5 mm
Operating conditions .....................................0 to +55 ºC, 0 – 95 % RH
Storage conditions.........................................-20 to +70 ºC, 0 – 95 % RH
Dimensions (W x H x D).................................102 x 25 x 96 mm
Weight ..............................................................179 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent the
technical status at the time of printing.
© Copyright 2015 by Conrad Electronic SE.
SP3, only 32 bit), Vista™ (32/64 bit),
7 (32/64 bit), 8, 8 Pro, 8 Enterprise,
8.1 (32/64 bit)
V1_0215_02-ETS-Mkd