Inhaltsverzeichnis
Werbung
5Fd - Go down anti-collision sensitivity setting
The desk has an Anti-Collision Sensitivity that will stop the desk's move-
ment if it hits something on the way down. You can change this Sensitivity
level by doing the following:
Press
M
and hold 3 seconds, handset display
M
again to enter, Display "1Un".
1. Press UP or DOWN, it will display 5Fd.
M
2. Press
to enter, it will display current anti-collision sensitivity level
L5 .Total 9 levels for down from
: most sensitivity setting |
3. Press UP or Down to select the your favorite level, press
wait 2 seconds, it will display current height.
6FS - Balance sensitivity
The desk has a balance Sensitivity to make sure the 2 columns always
work in the same position. You can change this Sensitivity level by doing
the following:
M
Press
and hold 3 seconds, handset display
M
again to enter, Display "1Un".
1. Press UP or DOWN ,It will display 6FS.
2.Press
M
button to enter, it will display current balance sensitivity level
L5. Total 9 levels for down from
: most sensitivity setting |
4. Press UP or Down to select the your favorite level, press
wait 2 seconds, it will display current height.
7SH - Setting the new min/max height range
The desk frame ships defaulted to its minimum and maximum height
limits. These steps allow the upper and lower limits to be adjusted to your
preference:
Press
M
and hold 3 seconds, handset display
M
again to enter, Display "1Un".
1. Press UP or DOWN, it will display 7FS.
M
2. Press
button to enter, it will display
will display
and
: Set the lowest position height display
: Set a new minimum desk height
: Set a new maximum desk height
5. Press UP or DOWN, it will display
will display current lowest height, press UP or DOWN to set the lowest
height display, press
M
to confirm.
6. Press UP or DOWN ,It will display
display current lowest height, press UP or DOWN to set a lowest height
M
position, press
to confirm.
7. Press UP or DOWN, it will display
play current highest height, press UP or DOWN to set a new highest height
position, press
M
to confirm.
, release
M
, press
to
.
least sensitivity setting
M
to confirm,
M
, release
, press
to
.
: least sensitivity setting
M
to confirm,
, release
M
, press
, press UP or DOWN, It
M
,press
button to enter, it
, press
M
to enter, it will
M
, press
to enter, it will dis-
8Hc - Setting Constant-touch & One-touch
M
Press
and hold 3 seconds, handset display
M
again to enter, Display "1Un".
1. Press UP or DOWN, it will display 8Hc
2. Press
M
to enter, it will display current mode
it will display
: Keep pressing UP or DOWN to make the desk moving up or down.
: Press UP or DOWN and release, the desk will moving up or down
automatically; press any button can stop the desk when it moving.
3. Press
M
to confirm the the way you need, wait 2 seconds, setting is
done.
9St - Time Reminder setting
To get a healthier working style,the desk can remind you to stand up when
you sit in a long time, you can set it by doing the following:
Press
M
and hold 3 seconds, handset display
M
again to enter, Display " 1Un".
1. Press UP or DOWN go get "9St"
M
2. Press
to enter,It will display
Hour)
3. Press UP or DOWN to select the time reminder you need, (
M
1.5 hours), press
to confirm.
Note: When handset time reminder beep, press any button to make it
disappear; the time reminder will last 30 seconds if no any operations.
10H - Setting bounce height
Press
M
and hold 3 seconds, handset display
M
again to enter, Display "1Un".
1. Press UP or Down to get 10H.
M
2. Press
to enter, it will show current bounce height.
3. Press UP or DOWN to get the bounce height, Press
2 seconds, it will display current height
11r - Restore Factory Defaults
M
Press
and hold 3 seconds, handset display
M
again to enter, Display "1Un".
1. Press UP or DOWN, it will display 11r
M
2. Press
to enter, it will display
M
3. Press
to confirm, wait 2 seconds, it will display current height.
12d - Fatigue test mode
Factory use, please ignore this programming.
11
M
, release
press
, press UP or DOWN,
, release
M
, press
,It no time reminder, (H means
means
,Release
M
, press
M
to confirm; wait
M
, release
, press
and flash.
Quicklinks ausblenden:
Werbung
Inhaltsverzeichnis
