Renkforce ST-OPM890 Bedienungsanleitung Seite 2

Operating instructions
Ergonomic USB Mouse ST-OPM890
Item no. 1486135
Intended use
The USB mouse is equipped with scroll wheel at the side and 5 buttons and is used for the
operation of your computer.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use
the product for purposes other than those described above, the product may be damaged.
In addition, improper use can cause hazards such as short circuiting, fire etc. Read the
instructions carefully and keep them. Make this product available to third parties only together
with its operating instructions.
This product complies with the statutory national and European requirements. All company
names and product names are trademarks of their respective owners. All rights reserved.
Delivery content
• Mouse
• Operating instructions
Up-to-date operating instructions
Download the latest operating instructions from our website www.conrad.com/downloads or
scan the printed QR code. Follow the instructions on the website.
Description of symbols
The symbol with an exclamation mark in a triangle indicates important instructions
contained in these operating instructions that must be followed.
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may become
dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high
humidity, moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and
protect it from any accidental use. Safe operation can no longer be guaranteed
if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height
can damage the product.
• Also observe the safety and operating instructions of any other devices which are
connected to the product.
• Consult an expert when in doubt about operation, safety or connection of the
device.
• Maintenance, modifications and repairs are to be performed exclusively by an
expert or at a qualified shop.
• If you have questions which remain unanswered by these operating instructions,
contact our technical support service or other technical personnel.
• Attention, LED light:
- Do not look directly into the LED light!
- Do not look into the beam directly or with optical instruments!
Operation
a) Connection and surfaces
• Place the mouse on a smooth, level and sufficiently large surface.
• The USB mouse's optical movement detection will not work on all surfaces.
- No operation is possible on reflective surfaces or glass.
- If you experience any difficulty moving the mouse pointer, use a suitable mouse pad.
- Take note, that the mouse can leave behind traces on sensitive surfaces.
• Connect the USB connector of the mouse with a unused USB port of your computer.
• The operating system detects new hardware and installs the required drivers. These are
included in the operating system.
b) Buttons and scroll wheel
Button Command
Left button Selecting, clicking; Configuration by operating system
Right button Call menu; Configuration by operating system
Scroll wheel with button Scrolling; Configuration by operating system
and Next page in web browser
Previous page in web browser
c) System-related settings
Open the mouse configuration menu in your operating system. Depending on the operating
system additional mouse settings can be performed, e.g. pointer speed.
Cleaning and care
• Remove the product from the computer before cleaning.
• Never submerge the product in water.
• If after an extended period of disuse the mouse pointer can no longer be moved correctly,
check the sensor beneath the mouse to see if it is dirty.
Clean the sensor by briefly blowing on it, or clean it with a soft, clean brush.
• Clean the product with a dry, fibre-free cloth.
• Do not use any abrasive or chemical cleaners.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the
household waste.
At the end of its service life, dispose of the product in accordance with applicable
regulatory guidelines.
You thus fulfill your statutory obligations and contribute to the protection of the environment.
Technical data
Input voltage / current ................... 5 V/DC, 500 mA via USB
USB .............................................. USB 2.0 and higher
Sampling rate ............................... 1000 dpi
Motion detection ........................... optical sensor
Cable length ................................. 150 cm
System requirements .................... Windows
Vista (32/64 bit), 7 (32/64 bit), 8 (32/64 bit),
8.1 (32/64 bit), 10 (32/64 bit), RT;
Mac OSX 10.2 or higher;
Linux Kernel 3.5.X
Operating conditions ..................... 10 to +60 ºC, 20 – 90 % RH (non condensing)
Storage conditions ........................ -20 to +60 ºC, 20 – 90 % RH (non condensing)
Dimensions (W x H x D) ............... 72 x 102 x 80 mm
Weight .......................................... 98 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represents the technical status at the time of printing.
Copyright 2016 by Conrad Electronic SE.
XP (with SP1, SP2, SP3) (32 bit),
®
*1486135_v1_0816_02_jh_m_en_(3)