Security Notes - Honeywell 041220 Montage, Anschluss, Anleitung

10
Table of contents
1. Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2. PCB design. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3. Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.1 Detector group inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.3 Relay outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4. Operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.1 Operation as 2-Relay 2-Input Module BUS-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.2 Operation as 5 Output Module BUS-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5. Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.1 BUS-2 address setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.2 Selection of module type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6. Installation guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
7. Connection diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
8. Final assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
9. Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Security notes

Read the instructions carefully and thoroughly before installing the device and putting it into
operation. They contain important information on installation, programming and operation.
The device is a state-of-the-art product. Only use the device:
- in accordance with regulations,
- iwhen it is has been installed and is functioning correctly,
- in accordance with technical data
The manufacturer is not responsible for damage that is caused by use not in accordance with regulations.
Installation and programming as well as maintenance and repair work may only be carried out by
skilled, authorized personnel.
De-energize the entire system before soldering and connecting.
Carry out soldering work with a temperature-controlled electrically isolated soldering iron.
Do not use the device in a potentially explosive environment or in rooms where metal
or plastic decomposing vapours are emitted.
ATTENTION! Important security notes to dangerous voltage operation
(Voltages 42,4 V peak value or 60 V DC, e.g. also 230 V AC):
³
- Work on primary voltage should only be carried out by
- Only connect units as per EN/ICE 60950-1 to the module.
- Appropriate overload protection must be provided in the mains circuit.
- For installation an appropriate mains separator is required.
- Switch off the primary circuit before carrying out installation or maintenance work.
- Do not lengthen or connect the activting line in the housing without double insulation.
- Do not store loose, unused connecting cables in the housing.
- Route the incoming cable separately through the provided recess to the terminal.
- Clearance: 4 mm, creapage distance: 5 mm.
- Strip the ends of the cores (approx. 4 mm).
- Use core end sleeves to clamp leads.
- Fix the incoming cable with the provided cable binder to the housing.
- The module only complies with the provisions of Protection Class ll when it is used in its original
state and for the intended purpose.
Observe the VDE safety regulations and provisions of the local electricity supplier.
Mounting and Connection Instructions 2-Relay 2-Input Module BUS-2, s.m.
³
skilled, authorized personnel
Page
.