The NIVO dropper post can handle a max. rider weight of 120 kg. Installation dimensions: You can easily find the suitable length for your NIVO dropper post by our online CONFIGURATOR: http://vecnum.com/en/products/nivo/configurator The NIVO dropper post is only manufactured exclusively with diameter 30,9 mm.
Seite 4
Operation instructions: Please make sure, that you are fully familiar with the function of the NIVO dropper post before your first ride. Due to an operating error you can loose control of your bike, which could lead to a serious accident.
Seite 5
We can only guarantee proper function of the NIVO dropper post if a tooLOC is used for clamping. Comparison between a conventional seat clamp and tooLOC seat clamp conventional seat clamp Forces / working load Clamping Forces Forces / working load...
1 - Installation preparation Measure most recent maximum Make sure to measure the distance between the end of the seat tube and the center of the rail clamp Remove old seatpost...
Seite 7
Install tooLOC clamp Torx T25 Extend NIVO...
2 - Change colored grip rings Remove the recent grip rings A - Seatpost not installed B - Seatpost already installed Remove and put on the grip Remove upper and lower rings via the lower end of rocker of the rail clamp. the seatpost.
Seite 9
Remove and put on the grip rings via the head of the seatpost. Fit the new o-rings into the groove...
3 - Install cable housing Install remote Push cable housing through the frame. Make sure the housing extends out of the seattube.
Seite 11
Install end cap Install cable in seatpost. Make sure the cable head is fixed by the o-ring.
Seite 12
Install the cable into the housing and plug end cap in the slot. Insert seatpost into the frame and set it to your desired seat height. For inserting the post, always push the seatpost. Do not pull the cable to insert the post.
Seite 13
Tighten seat clamp Torx T25 Determine housing length. Make sure to leave enough length for steering clearance. Define and mark the cut...
Seite 14
Loosen seat clamp 3.10 Torx T25 Pull seatpost out of the frame 3.11 until the housing extends out of the seattube. Unhook cable and cable housing 3.12 from the seatpost...
Seite 15
Remove cable from the housing 3.13 Cut housing at the mark 3.14 Install end cap 3.15...
4 - Bowden cable installation / replacement and adjustment Insert cable into housing Put thin oil on the cable to make it run smoother. Install cable in seatpost and plug end cap in the slot. Make sure the cable head is fixed by the o-ring.
Seite 17
Install cable and cable housing into your remote. Make sure the cable has no play. Before cutting the cable, check the function. 1. NIVO does not lock properly = Reduce cable tension 2. Remote has free travel = Increase cable tension...
5 - Feature options - (a) - TRAVEL FIT Maximum position max. 212mm travel Desired maximum position 22.5mm NIVO | 212 | 212mm - 180mm travel NIVO | 182 | 182mm - 150mm travel NIVO | 152 | 152mm - 120mm travel...
Seite 19
Loosen rear bolt Make sure to clean the head of the NIVO thoroughly. Dust and dirt getting inside of the seat post can cause damage to the mechanics. Remove lower rocker of the rail clamp...
Seite 20
Push the the remote lever and fit the travel by pushing the seatpost down to the tape marker Release remote. After releasing the remote, move seatpost a little bit up an down to make sure the position is locked. Lock TRAVEL FIT feature Reinstall the rubber cap and the rail clamp 5.10 Make sure to reinstall the rubber cap.
Seite 21
5 - Feature options - (b) - INDEXED Position 1 : pedalling ( maximum position = post completely extended) The maximum position should be adjusted to your ergonomic pedalling positions Position 2 : trail ( 40mm lowered referred to maximum position) This Position is ideal for riding an easy trail incl.
6 - Saddle installation Loosen rear bolt Remove bolt and nut from upper rocker of the rail clamp Put the saddle rail into the lower rocker of the rail clamp Put the upper rocker back onto the saddle rail Hang up the rear clamp bolt into the upper rocker...
Seite 23
Adjust saddle position Adjust saddle tilting first, then horizontal position -8.5° 8.5° 0° 73° default angle Tighten rear bolt to lower the saddle back Tighten front bolt to lower the saddle nose 32mm...
Seite 24
Tighten the clamp bolts 6-max. 8Nm Shake saddle strongly and check torque of the bolts again Please check torque of the clamping bolts after first couple of hours used. - Note maximum torque!
Seite 25
If you use an extreme tilting or a carbon saddle with high oval shaped rails, it may happen, that the standard M6x30m Titanium bolts do not reach the 6mm supporting thread. In our online shop https://shop.vecnum.com we offer longer bolts M6x35 for this special application...
Our advice: Dynamic Hochleistungsfett (available in many German bike online stores) For a long term reliability of your NIVO dropper post we recommend a relubrication of the upper sealing unit at least every 3 months. If you are running the post in dusty or muddy environment a relubrication after 1.5 month is helpful.
Seite 27
Put some grease onto the upper post tube Our recommendation: grease with low viscosity Slide back the seal housing and tighten it by hand. Clean the upper post tube from surplus grease.
The Vecnum GmbH grants a warranty of two years, as required by law. Wear by using the products is not covered by warranty. As all moving parts on the bike, also the NIVO dropper post needs the recommended maintenance and will show wear.
Augenmerk auf minimalen Serviceaufwand, Zuverlässigkeit, Langlebigkeit und Servicefreundlichkeit gelegt. Dadurch lassen sich alle gängigen Servicearbeiten mit gängigen Minitool-Werkzeugen erledigen. Bitte lies die Anleitung vor der Installation deiner NIVO Sattelstütze im Detail durch. Zusätzlich findest du unter http://vecnum.com/produkte/nivo/servicefaq/ immer die neueste Version der Bedienungsanleitung zum Download.
Seite 30
Inhalt 1 - Montagevorbereitung ................2 - Farbige Griffringe tauschen ..............3 - Zughülle montieren................4 - Zug montieren/tauschen und spannen ..........5 - Featureoptionen (a) TRAVEL FIT (b) INDEXED........6 - Sattel montieren ..................7 - Einfache Pflege und Wartung..............8 - Problembehebung und Service .............
Bedienung: Bitte mach dich unbedingt vor der ersten Fahrt mit der Funktion der verstellbaren Sattelstütze vertraut. Eine Fehlbedienung der NIVO Sattelstütze kann zum Kontrollverlust über das Fahrrad führen und dadurch einen Sturz mit schwerwiegenden Folgen verursachen. NIVO INDEXED: 4 verschiedene NIVO TRAVEL FIT: stufenlos verstellbar.
Seite 32
Wir garantieren die einwandfreie Funktion der Sattelstütze NIVO nur unter der Verwendung der Sattelklemme tooLOC. Vergleich Krafteinwirkungen herkömmliche Sattelstütze und tooLOC herkömmliche Sattelklemme KräfteBetriebsbelastung Klemmkräfte KräfteBetriebsbelastung ungleichmäßigeKrafteinwirkungaufdas gleichmäßigeKrafteinwirkungaufdas FührungsrohrderStütze. FührungsrohrderStütze DieskannzuFunktionseinschränkungender versenkbarenSattelstützeführen.
2 - Farbige Griffringe tauschen Vorinstallierte Ringe aus den Nuten rollen A - Sattelstütze nicht eingebaut B - Sattelstütze bereits eingebaut Ringe nach unten Beweglicher Teil des abnehmen und wieder Stützenkopfs lösen und auffädeln. abnehmen. Weiter mit 2.4...
Zug in Hülle einfädeln und die Zughülle mit der Endkappe in die Stütze stecken. Sattelstütze auf die gewünschte Sitzhöhe in den Rahmen schieben. Sattelstütze in den Rahmen schieben. Nicht mit dem Bowdenzug ziehen. Es muss sichergestellt sein das der Zug und die Hülle in der dafür vorgesehener Halterung montiert sind.
Sattelklemme anziehen Torx T25 Länge der Zughülle festlegen. Lenkeinschlag beachten Schnitt markieren...
Seite 41
Sattelklemme lösen 3.10 Torx T25 Sattelstütze wieder aus dem 3.11 Rahmen ziehen, bis die Hülle am Sitzrohr übersteht. Zug und Zughülle aus der Sattel- 3.12 stütze aushängen.
4 - Zug montieren/tauschen und spannen Zug in Zughülle fädeln Für eine geschmeidige Bedienung, dünnes Öl auf den Zug geben Zug in Hülle einfädeln und die Zughülle mit der Endkappe in die Stütze stecken...
Stütze nicht im Rahmen anstößt. Sattelklemme anziehen Torx T25 Zug und Zughülle in Daumenfernbedienung montieren und klemmen. Bowdenzug sollte kein Spiel haben. Vor dem Zug kürzen, Funktionstest machen. 1. NIVO verriegelt nicht = Zugspannung reduzieren 2. Daumenfernbedienung hat Leerweg = Zugspannung erhöhen...
Sattelstütze vollständig ausfahren Um die richtige Position einstellen zu können muss die Sattelstütze maximal ausgefahren sein. Hintere Schraube lösen Stützenkopf gründlich säubern. Staub und Schmutz dürfen nicht ins Innere gelangen. Die Mechanik kann dadurch Schaden nehmen. Unterer Teil des beweglichen Stützekopfs entnehmen und den oberen Teil nach vorne drehen.
Daumenfernbedienung auslösen und Sattelstüze zur Klebemarkierung herunterdrücken. Daumenfernbedieung loslassen Nach dem Loslassen der Daumenfernbedienung die Stütze etwas hoch und runter bewegen damit die Mechanik einrastet. TRAVEL FIT schließen Gummikappe und die beweglichen Teile 5.10 des Stützenkopfs wieder montieren. Die rote Gummikappe muss gut sitzen.
Seite 48
5 - Feature options - (b) - INDEXED Position 1 : Pedalieren (Maximalposition = Stütze max. ausgefahren ) Die Stütze sollte so im Sattelrohr positioniert werden, dass eine optimale ergonomische Sitzposition zum Pedalieren erreicht wird. Position 2 : Trail (40mm abgesenkt zur Maximalposition ) Diese Position eignet sich vor Allem zum Befahren von leichten Trails.
6 - Sattel montieren Hintere Schraube lösen Schraube und Mutter aus dem beweglichen Teil des Stützenkopfs nehmen Sattel mit dem Gestell in die Sattelauflagerillen legen Beweglichen Teil des Stützenkopfs auf das Sattelgestell legen Schraube und Mutter in den beweglichen Teil des Stützenkopfs einlegen...
Klemmschrauben abwechselnd Schritt für Schritt anziehen 6-max. 8Nm Kräftig am Sattel rütteln und bei Bedarf die Schrauben nochmal etwas anziehen Klemmschrauben nach ca. 1-2 Stunden Fahrtzeit nachziehen. - Drehmoment beachten!
Seite 52
Sattel optimal befestigt zu haben. Bei extremen Neigungswinkeln oder bei hochovalen Sattelgestellen kann es vorkommen, dass mit der mitglieferten M6x30 Klemmschraube die 6mm nicht eingehalten werden können. In unserem Shop auf https://shop.vecnum.com gibt es M6x35 Schrauben zum Nachrüsten.
7 - Einfache Pflege und Wartung Vor jeder Fahrt, Sattelstütze auf äußere Schäden und funktionale Einschränkung kontrollieren. Wir empfehlen für die Schmierung der oberen Dichteinheit ein dünnflüssiges Fett. Unsere Empfehlung: Dynamic Hochleistungsfett (im Fachhandel erhältlich) Um die Stütze lange und ohne Einschränkung fahren zu können, empfiehlt es sich spätestens nach 3 Monaten Betrieb die Dichtung zu schmieren.
Etwas Fett auf das obere Stützenrohr auftragen. Unsere Empfehlung: Dynamic Hochleistungsfett Dichtungsmutter zurück schieben und von Hand anziehen. Überschüssiges Fett vom oberen Stützenrohr abwischen.
Fragen schon klären lassen. 9 - Garantie und Gewährleistung Gewährleistung Die Vecnum GmbH gewährt auf die NIVO Sattelstütze die gesetzlich vorgeschriebene zweijährige Gewährleistung. Verschleiß durch normalen Gebrauch unterliegt nicht der Garantie. Wie alle beweglichen Teile am Bike erfordert auch die NIVO Sattelstütze entsprechende Wartung und unterliegt Verschleiß.
Seite 56
Vecnum GmbH Kommunikation Am-Angele-Hof 33 Telefon +49(0)7562.9743775 88316 Isny im Allgäu info@vecnum.com Deutschland www.vecnum.com 09-2020...