Renkforce 1296309 Gebrauchsanweisung Seite 3

Operating Instructions
6 Outlets rotating power strip with
surge protection
Item no. 1296309
Intended use
The power strip features 6 safety outlets to which appropriate devices can be connected. By the
illuminated on/off switch all outlets can be switched on or off simultaneously.
The power strip must be connected to a safety power socket outlet. See chapter "Technical
Data" for information on connection and the maximal permissible total power consumption of
all electrical loads connected.
The built-in surge protector can protect connected equipment from damage.
By means of the rotating mounting brackets the power strip can be fastened into place. This
design allows for the power strip to be turned forward or backward into the desired position.
This product is only to be installed and used indoors in dry conditions.
Always observe the safety instructions included in these operating instructions. Read the oper-
ating manual carefully; keep it in a safe place and/or pass it on to other users of the outlet strip.
Any use other than that described above could lead to damage to this product and involves risks
such as short circuits, fire, electric shock, etc. No part of the product may be modified or changed!
This product complies with the applicable national and European requirements. All names of
companies and products are the trademarks of the respective owners. All rights reserved.
Package contents
• Outlet strip
• Mounting material (4 screws)
• Operating instructions
Up-to-date operating instructions
Download the latest operating instructions at www.conrad.com/downloads or
scan the QR code shown. Follow the instructions on the website.
Explanation of symbols, inscriptions
The lightning symbol inside a triangle is a warning to inform you of potential risks of
personal injury, such as electric shock.
This symbol indicates specific risks associated with handling, operation or use.
The "arrow" symbol indicates special tips and operating information.
The product is only intended to be installed and used in dry, indoor rooms; it must
not get damp or wet.
Observe the operating instructions!
Safety Instructions
Damage due to not following these operating instructions will void the war-
ranty! We do not assume any liability for any resulting damage!
We do not assume any liability for material and personal damage caused by
improper use or non-compliance with the safety instructions! In such cases,
the warranty will be null and void!
a) General
• The unauthorised conversion and/or modification of the product is not permitted
for safety and approval reasons. Do not open/disassemble! Contains no custom-
er-serviceable parts.
Maintenance, adjustment or repair work may only be carried out by an expert/
authorised service centre, which is familiar with the hazards involved and the
relevant regulations.
• The product is designed according to protection class I. It may only be used when
connected to an earthed mains socket.
The electrical outlet must be located in direct proximity to the product and easily
accessible.
• The product is equipped with a protection against accidental contact. An inte-
grated mechanism will release the holes of the receptacle only, if the two prongs
of a power plug are inserted into the two holes at once.
• Take special caution when children are around. Children cannot recognize the
danger arising from the incorrect use of electrical devices. There is a risk of a
life-threatening electric shock!
• The product is not a toy and must be kept out of the reach of children. Position the
product so it is out of the reach of children.
• Do not carelessly leave the packaging material lying around since this may be-
come a dangerous toy for children.
• Handle the product with care; it may be damaged by impacts, blows, or accidental
falls, even from a low height.
b) Installation location
• The product may be used in dry, enclosed indoor areas only; it must not get damp
or wet! Never set up the product in the direct vicinity of a bathroom, shower,
bathtub or similar. There is a risk of a life-threatening electric shock!
• The product must not be exposed to extreme temperatures, direct sunlight or
strong vibrations.
• Completely unwind the mains cable during use. The power cable must not be
pinched or damaged by contact with sharp edges. Do not place any objects on
the cable, and do not allow it to become kinked. Install the cable where no one can
stumble over it and the plug is easily accessible. Do not install the mains cable
under carpets or the like.
• Do not operate the device in environments where there are high levels of dust,
flammable gases, vapours or solvents. There is a danger of fire and explosion!
c) Handling and use
• Never touch, operate, plug in or unplug the product with damp or wet hands.
There is a risk of a life-threatening electric shock!
• Never connect the product to the power supply immediately after it has been
transferred from a cold room into a warm one (e.g., during transport). The conden-
sation that develops in such cases could damage the device or cause an electric
shock! Allow the product to reach room temperature. Wait until the condensation
has evaporated. This might take several hours. Only after this should the product
be plugged into the power supply and put into use.
• Always pull a mains plug on the gripping surface intended for this purpose. Never
unplug the mains plug from a mains socket by pulling the cable!
• Do not overload the outlet strip. Observe the maximal permissible total power
consumption of all electrical loads connected as per chapter "Technical Data".
• Do not connect in series! This can lead to an overloading of the outlet strip! There
is a risk of fire!
Plug the earthed mains plug of the outlet strip directly, e.g., into a wall socket. Do
not connect other outlet strips to this outlet strip.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights
including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represents the technical status at the time of printing.
Copyright 2020 by Conrad Electronic SE. *1296309_v3_0620_02_dh_m_3L