Datalogic AMT58-S 13x14 PN-Serie Montagehinweise

Series
Complete documentation
available for download at
www.datalogic.com
EN Mounting instructions
 Mount the flexible coupling 1 on the encoder shaft;
 fix the encoder either to the flange 2 or to the mounting bell by means of
screws 3;
 mount the flexible coupling 1 on the motor shaft, then secure either the flange
2 to the support (or the mounting bell to the motor);
 make sure the misalignment tolerances of the flexible coupling 1 are
respected.
ES Instrucciones de montaje
 Montar el acoplamiento elástico 1 en el eje del encoder;
 fijar el encoder a la brida 2 (o a la campana) mediante los tornillos 3;
 montar el acoplamiento elástico 1 en el eje del motor, después fijar la brida
2 al soporte (o la campana al motor);
 asegurarse de que se respetan las tolerancias de desalineaci ón permitidas por
el acoplamiento elástico 1.
a [mm] b [mm]
36 H7 48
M12 4-pin
Male, A coding
Description Pin
PWR POWER
SUPPLY
+10VDC +30VDC 1
n.c. 2
0VDC 3
n.c. 4
M12 4-pin
Description Pin Female, D coding
PORT 1, PORT 2
Tx Data + 1
Rx Data + 2
Tx Data - 3
Rx Data - 4
AMT58-Sxx-13x14 PN
IT
 Fissare il giunto elastico 1 all'encoder;
 fissare l'encoder alla flangia di fissaggio 2 o alla campana utilizzando le viti 3;
 fissare il giunto elastico 1 al motore, poi fissare la flangia 2 al supporto o la
campana al motore;
 assicurarsi che le tolleranze di disallineamento ammesse dal giunto elastico 1
siano rispettate.
FR
 Monter le joint élastique 1 sur l'arbre du codeur;
 fixer le codeur à la bride 2 (ou à la cloche de montage) au moyen des vis 3;
 monter le joint élastique 1 sur l'arbre du moteur; puis fixer la bride 2 au
support (ou la cloche de montage au moteur);
 s'assurer que les tolérances de mauvais alignement admises par le joint
élastique 1 soient respectées.
c [mm] d [mm]
a [mm]
- - 36 H7
Connector type
Frontal side
Lato contatti
Aufsicht Stiftseite
Lado contactos
Côté contacts
Istruzioni di montaggio
Instructions de montage
with fixing clamps ST-58-KIT
b [mm] c [mm]
- 67
Link 1: link to another Ethernet component
L1 (green)
on port 1
Activity 1: incoming and outgoing traffic on
A1 (yellow)
port 1
Status 1: see table below
S1 (green)
S1 Status1 S2 Status 2
green red
OFF OFF
ON ON
ON Blinking (1 Hz)
OFF ON
On OFF
Blinking (1 Hz) OFF
OFF Blinking (1 Hz) Flash memory upgrade failed
ENCODERS
DE Montagehinweise
 Die Kupplung 1 auf den Geber montieren;
 geber mit dem Flansch 2 bzw. der Montageglocke mittels Schrauben 3
verschrauben;
 die Kupplung 1 auf die Motorwelle montieren und den Flansch 2 auf seiner
Auflage bzw. die Montageglocke am Motor fixieren;
 es muss sichergestellt sein, dass die zulässigen Toleranzen der Kupplung 1
eingehalten werden.
with flange ST-58-FLNG
d [mm]
-
DIAGNOSTIC LEDs
Link 2: link to another Ethernet component on
L2 (green)
port 2
Activity 2: incoming and outgoing traffic on port
A2 (yellow)
2
Status 2: see table below
S2 (red)
Meaning
No power
No connection (no data exchange) Bus disconnected, Master not available
Parametrization fault (no data Slave not configured yet or wrong
exchange) configuration
Diagnosis exists, slave in data exchange
System failure
mode
Data exchange, Slave ok
Flash memory upgrade active Upgrading the flash memory
No connection
Installation has to be carried out with power supply disconnected.
L'installazione deve essere eseguita in assenza di tensione.
Der Anschluss darf nur bei ausgeschalteter Versorgungsspannung erfolgen.
La instalación sólo debe ser efectuada en ausencia total de tensión.
Le montage du dispositif doit être effectué en absence totale de tension.
Absolute encoders
Cause