Renkforce WS-WN575A2 Bedienungsanleitung Seite 6

Manual configuration of repeater
• After completing the basic configuration, click on the blue, square button in the upper left
corner to start the set-up.
• First select the WLAN to which you want to connect the repeater or which you want to
amplify by clicking in the list.
To update the list, click on the right button at the bottom.
• The WLAN name is automatically transferred from your router. In addition, the name will get
an add-on. You can also change it to what you like.
• Now enter the password in the free field of the WLAN network that you have previously
selected.
• To close, click the left confirmation button. Once the changes have been applied, the set-up
is complete.
If you have performed the configuration via WLAN, you must now still connect your
device to the new WLAN network.
If you still want to change other settings, simply log in again on the web interface.
Positioning the repeater
• Once you have finished configuring the repeater, you should position it correctly, as shown
in the following image.
• Try different locations and finally select the installation spot with the best connection to your
existing wireless router.
• To prevent the repeater from being too far away from your WLAN router, you should have
at least 2 LEDs shining on the WLAN display.
Resetting to factory settings
Proceed as follows to reset the product to factory settings.
• Plug the device into a mains socket.
• Switch it on using the slide switch (3) and wait until the start procedure is completed.
• Press and hold the recessed button (1) for more than 3 seconds. Then release the button
again.
• The product will restart with the factory settings. This process lasts approx. 2 minutes.
Care and cleaning
Do not use abrasive cleaning agents, cleaning alcohol or other chemical solutions
since these could damage the housing or even impair operation.
• Before cleaning, unplug the product from the wall socket and remove all connection cables.
• Use a dry, lint-free cloth to clean the product.
Disposal
Electrical and electronic equipment does not belong in the regular household waste.
Once the product becomes unusable, dispose of it in accordance with the relevant
statutory regulations.
Declaration of conformity (DOC)
We, Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau, hereby declare that this
product conforms to the 2014/53/EU directive.
The full text of the EU conformity declaration is available via the following Internet
address: www.conrad.com/downloads
Select a language by clicking a flag symbol and enter the order number of the pro-
duct in the search field; then you will be able to download the EU declaration of
conformity in PDF format.
Technical data
Operating voltage ................................. 100 - 240 V/AC, 50/60 Hz, max. 0.3 A
Connections .......................................... 1x RJ45 LAN 100 Mbit; 1x RF45 WAN/LAN 100 MBit
WLAN .................................................. IEEE802.11b/g/n, 2.4 GHz, max. 300 MBit;
Frequency range/
transmitting capacity ............................. 2.412 – 2.472 GHz, 17.62 dBm;
Encryption protocols ............................ WPA2; EPA; WEP
Operating modes ................................. Repeater; access point; router
Dimensions (W x H x D) ....................... approx. 50 x 73 x 52 mm (without antenna)
Dimensions (Ø x L) ............................... approx. 10 x 91 mm
Weight .................................................. approx. 102 g
Operating conditions ............................. 0 °C to +40 °C, 10 - 90% RH (non-condensing)
Storage conditions ............................... -10 °C to +70 °C, 10 - 90% RH (non-condensing)
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
© Copyright 2019 by Conrad Electronic SE.
IEEE802.11a/n/ac, 5 GHz, max. 433 MBit;
5.180 – 5.240 GHz, 13.13 dBm
1902085_V1_0519_02_m_VTP_en