Renkforce 2249725 Bedienungsanleitung Seite 3

Operating Instructions
USB-C Hub for Wireless Image Transmission
Item No. 2249725
Intended use
The product is a multi-functional USB-C hub that can be used to wirelessly cast a display. A
transmitter encodes a video signal from devices such as a mobile phone or laptop and sends
it wirelessly to the receiver which is connected to a display input. The transmission range is
approximately 10 m.
It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in
bathrooms, must be avoided under all circumstances.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use
the product for purposes other than those described above, the product may be damaged. In
addition, improper use can result in or other hazards. Read the instructions carefully and store
them in a safe place. Make this product available to third parties only together with its operating
instructions.
This product complies with the statutory national and European requirements. All company
names and product names are trademarks of their respective owners. All rights reserved.
HDMI is a registered trademark of HDMI Licensing L.L.C.
Delivery content
• Transmitter
• Receiver
• USB-C to USB-A power cable
• Operating instructions
Up-to-date operating instructions
Download the latest operating instructions at www.conrad.com/downloads or
scan the QR code shown. Follow the instructions on the website.
Explanation of symbols
The symbol with the exclamation mark in the triangle is used to indicate important
information in these operating instructions. Always read this information carefully.
The arrow symbol indicates special information and advice on operation.
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information
on proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
a) General information
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become
dangerous playing material for children.
• Protect the appliance from extreme temperatures, direct sunlight, strong jolts, high
humidity, moisture, flammable gases, steam and solvents.
Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and
protect it from any accidental use. Safe operation can no longer be guaranteed
if the product:
• is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height
can damage the product.
• Consult an expert when in doubt about the operation, safety or connection of the
appliance.
• Maintenance, modifications and repairs must only be completed by a technician
or an authorised repair centre.
• If you have questions which remain unanswered by these operating instructions,
contact our technical support service or other technical personnel.
b) Connected devices
• Also observe the safety and operating instructions of any other devices which are
connected to the product.
Operating elements
1 2
8 4 5 6 7
9 10 11 12 13
Connection diagram
Before connecting the receiver to the power supply using the included cable, make
sure that the USB-A power source (3) can deliver sufficient current (see "Technical
data") otherwise you may damage the source. Do not use a USB-A port of a
computer, keyboard or USB-A hub without a power adapter as the current supplied
by these ports is insufficient.
a) Diagram
USB-C Audio VGA
5V/2A
b) USB hub (receiver)
1. Connect the USB-C power input (10) to a suitable power supply using the included cable.
2. Connect the VGA out (12) or HDMI out (13) to a display (cable not included).
HDMI & VGA can work simultaneously.
c) Display hub (transmitter)
1. On the transmitter, connect the USB-C connector (3) to a USB-C port on your computer.
Wait a few moments for the device to register with the operating system.
The computer display may reconfigure slightly when the hub is connected to your computer,
this is normal.
2. Press the function button (2) to mirror the display. If the display does not mirror, refer to
section "Pairing transmitter with receiver".
Refer to your device operating system instructions for further information relating to
display settings such as using as a separate display.
The device will appear under the name "Phoneix2019".
Pairing transmitter with receiver
1. On the receiver, press and hold the function button (9) 5 sec, the screen will show "wait
for pairing!"
2. On the transmitter, press and hold the function button (2) 5 sec.
3. Your computer will mirror to the connected display when pairing is successful.
The pairing process can take up to 15 seconds to complete.
Transmitter
1 LED indicator
2 Function button
3
3 USB-C connector
4 USB-A port
5 USB-A port
6 SD card reader
7 Micro SD card reader
Receiver
8 LED indicator
9 Function button
10 USB-C power input
11 3.5 mm audio output jack
12 VGA out
13 HDMI out
Mobile
Laptop
Tablet PC
Monitor
Projector
TV