Redstone HM120L Original Bedienungsanleitung Seite 29

• With the drag guide (23) fixed in place:
use the handle (1) to move the machine head (5)
steadily and with light pressure downwards until
the saw blade (7) has completely cut through the
work piece.
• With the drag guide (23) not fixed in place:
pull the machine head (5) all the way to the front.
Lower the handle (1) to the very bottom by applying
steady and light downward pressure. Now push the
machine head (5) slowly and steadily to the very
back until the saw blade (7) has completely cut
through the work piece.
• When the cutting operation is completed, move the
machine head (5) back to its upper (home) position
and release the ON/OFF button (2).
Attention! The machine executes an upward
stroke automatically due to the return spring, i.e.
do not release the handle (1) after completing the
cut; instead allow the machine head to move up-
wards slowly whilst applying light counter pres-
sure.
8.5 Cross cut 90° and turntable 0°- 45°
(Fig. 1, 2, 11, 12)
The crosscut saw can be used to make crosscuts of
0°-45° to the left and 0°-45° to the right in relation
to the stop rail.
Attention! For bevel cuts (inclined saw head), the
moveable stop rail (28) must be fixed in the outer
position on both sides. (see Fig. 11)
• Open the set screw (29) on the moveable stop
rail (28) and push the moveable stop rail (28) out-
wards.
• The moveable stop rail (28) must be locked in a
position far enough from the inner position that
the distance between the stop rail (28) and the
saw blade (7) is no more than 5 mm. (see Fig. 12)
• Before making the cut, check that no collision
could occur between the stop rail (28) and the saw
blade (7).
• Tighten the set screw (29) again.
• Loosen the locking handle (13) counterclockwise
and pull the indexed position lever (12) with the
index finger at top.
• Set the turntable (16) to the desired angle by us-
ing the locking handle (13). The pointer (14) on the
turntable (16) must match with the desired angular
scale (15) on the fixed saw table (17).
• Turn the locking handle (13) clockwise to fix the
turntable (16).
• Cut as described under section 8.4.
8.6 Mitre cut 0°- 45° and turntable 0°
(Fig. 1, 2, 11-14)
The crosscut saw can be used to make mitre cuts
of 0° - 45° to left/right in relation to the work face.
Important. To make miter cuts (inclined saw
head), the adjustable stop rail (28a/28b) must be
fixed at the outer position.
• Open the locking screw (29) for the adjustable stop
rail (28) and push the adjustable stop rail (of in-
clined side) outwards. (see Fig. 13+14)
• The other adjustable stop rail (28) must be fixed
far enough in front of the innermost position that
the distance between the stop rail (28) and the
saw blade (7) amounts to a maximum of 5 mm.
(see Fig. 12)
• Before making a cut, check that the stop rail (28)
and the saw blade (7) cannot collide.
• Secure the locking screw (29) again.
• Move the machine head (5) to the top position.
• Fix the rotary table (16) in the 0° position.
• Loosen the locking lever (22) and use the handle
(1) to angle the machine head (5) to the left/right,
until the pointer (20) indicates the desired angle
measurement on the scale (19).
• Re-tighten the locking lever (22).
• Cut as described in section 8.4.
8.7 Mitre cut 0°- 45° and turntable 0°- 45°
(Fig. 1, 2, 11-14)
The crosscut saw can be used to make mitre cuts
to the left/right of 0°- 45° in relation to the work face
and, at the same time, 0°- 45° to the left or 0°- 45° to
the right in relation to the stop rail (double mitre cut).
Important. To make miter cuts (inclined saw
head), the adjustable stop rail (28) must be fixed
at the outer position.
• Open the locking screw (29) for the adjustable stop
rail (28a/28b) and push the adjustable stop rail (of
inclined side) outwards. (see Fig. 13+14)
• The other adjustable stop rail (28) must be fixed
far enough in front of the innermost position that
the distance between the stop rail (28) and the
saw blade (7) amounts to a maximum of 5 mm.
(see Fig. 12)
• Before making a cut, check that the stop rail (28)
and the saw blade (7) cannot collide.
• Secure the locking screw (29) again.
• Move the machine head (5) to its upper position.
• Loosen the locking handle (13) counterclockwise
and pull the indexed position lever (12) with the
index finger at top.
• Set the turntable (16) to the desired angle by us-
ing the locking handle (13). The pointer (14) on the
turntable (16) must match with the desired angular
scale (15) on the fixed saw table (17).
• Turn the locking handle (13) clockwise to fix the
turntable (16).
• Loosening the locking lever (22).
GB | 29