TFA 35.1156 Bedienungsanleitung Seite 14

01_TFA_No. 35.1156_Anleitung 29.11.2019
METEOTIME PRIMO – Weather Info Center
• The test takes about 1 minute. You can start the test with the TEST
pressing the TEST button.
7.2 Switch time + date ↔ city ↔ alarm
• You can press the SET button to switch from the display of the time and date to city, weekday alarm (W-ALM),
single alarm (S-ALM) and pre-alarm (P-ALM).
7.3 Select country and city
• Press and hold the SET button for 3 seconds in normal mode,
display. Press the + or – button to select the country. For instance: If
selected "Germany".
• Press the SET button to confirm the country.
• Then, press the + or – button to select the city. For instance
• Press and hold the + or – button for fast mode.
• Press the SET button to accept the setting.
EINST.VORG
• On the display appears . (EXIT in English).
• A table for the choice of location can be found in the Meteotime Booklet.
7.3.1 Activate favourites
• Once you have set your city as described above, you may select more cities for easy access.
• Instead of terminating the setting with the SET button, continue as follows:
• If 'Frankfurt/Main' is your selection as one of your favourite cities, then press the TEST
will be shown on top of your selected city, and it will be stored into your personal memory list.
• Now, you can press the + or – button to select more cities in the same country, and then press the TEST
button to confirm.
• If you wish to select cities from different countries, exit the setting with the SET button and re-enter it again as
described above in order to change the country.
• You may select a maximum of five cities as favourites. If you want to add more cities, then
(MEMFULL in English) appears on the display.
• When all settings are done, press the SET button to confirm and exit the setting mode.
NOTE: If after inserting the batteries for the first time, you are skipping the city selection, the device will select
"Frankfurt/Main" as your selected city by default.
26
6:59 Uhr Seite 14
button and end the test at any time by
LAND EINST. (COUNTRY in English) appears on the
D/GER appears in the info box, you have
STADT EINST. (CITY in English) appears on the display.
frankfurtM
is the city of Frankfurt/Main.
button to confirm. A
METEOTIME PRIMO – Weather Info Center
7.3.1.1 Display of favourites
• If you have selected more than one city as favourite, for example "Frankfurt/Main", "Paris" and "Stockholm", then
you are able to scroll through these cities by pressing the - button when the name of the city appears on the dis-
play. (Press the SET button until it shows the city's name).
frankfurtM
7.3.1.2 Remove a city from the favorites list
• Press and hold the SET button for 3 seconds.
the + or – button to select the country.
• Press the SET button to confirm the country.
• Then press the + or – button to select the city with the
• Press the TEST button to remove the
• Repeat this if you wish to remove more cities from your list.
• Now, you can also press the + or – button to select another favourite city.
• Once you have made all your changes, press the SET button to quit.
the display. After 4 seconds, it will go to the Date-Time Mode.
7.3.2 Personalize your place name
• Press and hold the SET button for 3 seconds.
+ or – button to select the country. If
• Press the SET button to confirm the country. On the display appears
• Then, press the + or – button to select the city, and the city's name appears on the display, for instance
furtM . You can now enter a new city near Frankfurt am Main.
• Press the MEM button; a cursor flashes on the first position of the information window.
SPEICHER .V
Apply the following input commands:
Button Function
+ or – Selection of a letter
PARIS STOCKHOLM
[–] [–]
LAND EINST.
(COUNTRY in English) appears on the display. Press
.
. Now this city is removed from the favourites.
EINST.VORG. (EXIT in English) appears on
LAND EINST.
(COUNTRY in English) appears on the display. Press the
D/GER appears, you have selected "Germany".
STADT EINST.
(CITY in English).
frank-
27