Starting Operation - Bosch EasyPump Originalbetriebsanleitung

Typically, the A-weighted sound pressure level of the power
tool is 71 dB(A). Uncertainty K = 3 dB. The noise level when
working can exceed the volume stated. Wear hearing pro-
tection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 62841‑1:
2 2
a = 4 m/s , K = 1.5 m/s .
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Assembly
Battery Charging (see figure A)
Use only the power supplies listed in the technical
u
data. Only these power supplies are matched to the lith-
ium-ion battery of your air pump.
Note: The battery is supplied partially charged. To ensure
the maximum performance of the battery, use the power
supply to fully charge the battery before first use.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by "Electronic Cell Protection (ECP)". A protective circuit
switches the air pump off when the battery is drained.
Do not continue to press the on/off button after the
u
air pump has automatically switched itself off due to
an empty battery. This can damage the rechargeable
battery.
To charge the battery, connect the USB Type-C® port (16) to
the power supply (15) via the USB cable (14). Plug the
power supply into a plug socket.
The charging process will begin and will be indicated by con-
tinuously filling bars in the battery charge indicator (d). The
air pump cannot be used during charging.
Bosch Power Tools
When the charging process is complete, the battery charge
indicator (d) will be continuously lit until the air pump is dis-
connected from the power supply.
If you are not planning to use the air pump again soon, dis-
connect the power supply (15) from the mains.
Battery Charge Indicator
The battery charge indicator (d) in the display shows the
battery's state of charge:
Display Capacity
75−100 %
50−75 %
25−50 %
5−25 %
0−5 %
Fitting/Changing the Adapter (see figure B)
Select the adapter best suited to the intended application:
– Valve adapter (2), e.g. for many bike valves.
– Ball needle adapter (3), e.g. for footballs.
– Volume adapter (4), for small beach items or sporting
goods, e.g. beach balls.
Slide the lid off the adapter storage compartment (1) and re-
move the adapter.
Screw the adapter fully into the pressure hose (9).
For standard car tyre valves (sometimes also used on bikes),
no adapter is required.
Operation

Starting Operation

Switching On and Off
To switch the air pump on or off, press the on/off but-
ton (5). The last set target pressure is saved when switching
off the pump.
When no button on the air pump is pressed for approx.
3 minutes, the air pump automatically switches off to pre-
serve battery life.
Switching the worklight on and off
To switch the worklight (12) on and off, press the change
unit/worklight button (7) for approximately 1 second.
Do not look directly into the worklight; it can blind
u
you.
Changing the Unit of Measurement
For the pressure indicator, the units bar, psi and kPa are
available.
To change the unit of measurement, short press the change
unit/worklight button (7) as many times as needed until the
required unit of measurement appears in the unit of meas-
urement indicator (a).
English | 13
1 609 92A 5NV | (14.07.2020)