Technical Specification - Sharp PS-940 Bedienungsanleitung

6
FLASHING LIGHT
To activate the light functions, you must switch AUDIO-2 to AUX mode.
1. Long press the LIGHT button to turn on/off the decoration LED
lighting around the speakers.
2. Press the LIGHT button repeatedly to choose the lighting mode for
the inner lights:
L-1: Blue LED will be on constantly.
L-2: Red LED will be on constantly.
L-3: Green LED will be on constantly.
L-4: Three-colors fl ash in gradual mode.
L-5: Seven-colors fl ash in gradual mode.
L-6: Three-colors dance with the music.
Press one more time to turn off .
BLUETOOTH OPERATION
1. Rotate the AUDIO-1 knob to BT mode to enter Bluetooth mode, " - bt -
" will be lit up and fl ash on the display screen.
2. Turn on the Bluetooth function on your device, scan "SHARP PS-940"
and connect. Input the password 0000 if required.
3. Once successfully connected, there will be a prompt sound and " - bt - "
will stop fl ashing.
4. Adjust the EQ eff ect by sliding the EQ SLIDER-A.
5. Rotate the A-VOLUME knob or adjust the volume on the external
device to increase or decrease the music volume to your desired level.
6. Control the playback with your audio device.
7. Press the BLUETOOTH CONNECTION button to disconnect the
bluetooth connection.
Wireless connection with multiple PS-940 (connect to the compatible
speakers).
1. Select a PS-940 as the host speaker. Long press the BLUETOOTH
CONNECTION button, " bt - " will be shown on the display screen.
2. Continuously press the BLUETOOTH CONNECTION button twice on
another one or more PS-940. When " - bt " shown on the display,
it means the speakers have been connected to the host speaker
successfully.
3. Make your device connect to the host speaker. Then you can enjoy the
music via your the speakers.
NOTES: The product supports 3 phones (except for Iphone) to establish
bluetooth connection at the same time.
USB OPERATION
This unit provides two USB ports, one for playback, and another for
charging.
1. Set AUDIO-1 to USB mode. " - USb -" will be shown on the display.
2. Plug the USB memory stick to the USB PLAYBACK PORT on the unit.
Playback will start automatically from track 01.
3. To pause the playback, press the PLAY/PAUSE button on the top panel
of the unit. Press this button again to resume the playback.
4. To select a desired track, press the PREVIOUS or NEXT button
respectively during playing until the desired track appears on the
display. The unit will start to play automatically.
AUX-IN OPERATION
1. Set the AUDIO-1 to AUX mode, "AUX" will be shown on the display.
2. Connect your audio device to the AUX IN JACK on the top panel of the
unit with an AUX IN cable.
3. Rotate the A-VOLUME knob to adjust the music volume.
4. Use the EQ SLIDER-A to adjust your favor sound eff ect.
5. Control the playback with your audio device.
MIC/GUITAR OPERATION
1. Set the AUDIO-2 to MIC/GUITAR mode.
2. Connect your microphone/guitar to the MIC or GUITAR JACK.
3. Rotate the B-VOLUME knob to adjust the microphone/guitar volume.
4. Use the EQ SLIDER-B to adjust your favor sound eff ect.
NOTES: The EQ SLIDER-B cannot work if the AUDIO-2 is set to AUX mode.
Technical specifi cation
Model
Power Supply
Rated Power Consumption
Standby Power Consumption
Output Power
Total max power output
Frequency Response
Battery
Bluetooth
Version
Maximum power transmitted
Frequency bands
NOTE: Specifi cations are subject to change for continuous improvement
without prior notice.
224mm
PS-940
AC ~ 100-240V, 50/60Hz
20W
<0.5W
2 x 25 W (RMS)
180 W
40Hz-15KHz
Built-in 37,44Wh Li-ion battery
battery pack with 4x 2.600 mAh
V 4.0
<20 dbm
2402 MHz ~ 2480 MHz
635mm
300mm
8,0 kg