Werbung
Verfügbare Sprachen
Verfügbare Sprachen
80330 Disinfectant holder
Please read these assembly instructions carefully!
TECHNICAL DATA
DIMENSIONS
- Bottle size:
width x depth: max. ø/
- Clamping range:
depth 65 - 102 mm
- Drip cup:
ø 70 x 47 mm
MATERIAL
- Mounting bracket:
Steel
- Drip cup:
Polyamide
- Knurled knobs:
Polyamide, steel, zinc
- Screwing material:
Steel, brass, zinc
SURFACE
pure white, powder-coated
WEIGHT
0.6 kg
SAFETY INSTRUCTIONS
The safety of the stand depends on the:
MOUNTING
Ensure that all screw connection are tight.
WALL CONDITION
Only use the product on suitable walls, i.e. mount only on
load-bearing walls. Weak walls are unsuited as well as wall
areas where running wires and pipes are hidden behind. The
screws and dowels 2 supplied are not convenient for all
walls. In case of any doubt consult a qualified expert.
LOAD
Only for disinfectant bottles with suitable size;
see above TECHNICAL DATA.
SURROUNDINGS
Please avoid respectively prevent negative
external influences (knocks, dragging, vibrations,
wind, humidity etc.)
INSTALLATION INSTRUCTIONS
A. COMPONENTS
1 Wall holder
1.a Mounting bracket
1.b Drip cup (clipped in)
2 Accessories bag (6-16312-1-00)
2.a Wood screw 4,5 x 35 mm (2x)
2.b Anchor (plastic) ø 6 x 30 mm (2x)
3 Accessories bag (6-80310-1-76)
3.a Knurled knob M5 (2x)
3.b Washer ø 5,3 mm (2x)
3.c Carriage bolt M5 x 12 mm (2x)
3.d Clamping bracket
B. WALL MOUNTING
4 see fig. 4.1 - 4.5
C. PREPARING DISINFECTANT HOLDER
5 Open the accessories bag 3:
5
Fitting the clamping bracket 3.d to the wall holder 1:
6
- Slide the bracket 3.d from outside over the
6 -
mounting bracket,
6
- insert the carriage bolts 3.c from the inside,
- thrust washers 3.b over the threads,
6
6
- screw on knurled knobs 3.a.
6 The drip cup 1.d can be removed for cleaning purposes.
7
Subsequently press the drip cup from above back
7
into the holder.
D. DISINFECTANT BOTTLE (not included in delivery)
7 Place the disinfectant bottle in the bottle holder,
8 clamp the bottle by means of the bracket 3.d,
9 tighten both knurled knobs 3.a.
INFORMATION
NOTE: The disinfectant holder is not a
NOTE:
medically certified product.
- Negative effects of the disinfectant on the products
-
(surfaces, material) are not known to us.
- Nevertheless, we recommend to always remove possible
-
residues of the disinfectant in order to avoid possible
-
damage and to enjoy the product as long as possible.
- For cleaning purposes use a slightly damp cloth and
-
a non-abrasive cleaning agent.
Disinfectant is not included in the scope of delivery.
■
102 mm
PREPARING
4.1 Align mounting bracket
4.1
vertically
4.2 Mark the drill holes.
C. PREPARING HOLDER
A. COMPONENTS
B. WALL MOUNTING
4.3 Pre-drilling
4.4 WOODEN BEAM
4.3
e.g.: ø 6 mm
- Wood screw 4,5 x 35 mm 2.a
4.3
Expansion anchor
drill,
4.3
ø 3 mm Wood
countersink,
4.3
screw
blow out,
attach bracket,
screw in wood screws
MOUNTEXAMPLES
4.5 PERFORATED BRICKS,
4.5
CONCRETE
- Plastic anchor 6 x 30 mm 2.b
-
with wood screw 4,5 x 35 mm 2.a
drill, countersink, blow out,
set the anchor,
attach bracket, screw in wood
screws
D. DISINFECTANT BOTTLE
KÖNIG & MEYER GmbH & Co. KG
Kiesweg 2, 97877 Wertheim, www.k-m.de
80330-000-76 Rev.7a 03-79-905-00 5/20
Werbung
