Maintenance - Status Mpr45 Originalbetriebsanleitung

5. MAINTENANCE

WARNING: For operating with chisels switch 5 shall always be in "hammer" (
position. The angle of the chisel setting can be adjusted in the mode (
by switching to the mode ( )
Removing the SDS-Plus tool (Fig.B)
Pull the locking clutch (2) entirely back and take the tool (1) out.
Auxiliary handle
Always use the auxiliary handle (7).
Loosen the handle by turning it left wise. Turn the handle in the most convenient for
operation position, and then tighten it well.
Do not carry the machine by a loose auxiliary handle.
You can fix the drilling depth through depth gauge (3).
The depth gauge (3) can be fixed by screw (4).
RECOMMENDATIONS FOR OPERATION
Apply moderate pressure during operation! Higher pressure will not increase
efficiency when drilling and chiselling, but it will lead to decreasing the operation
life of the machine.
Take the drill bit out of the opening from time to time to remove dust.
Watch out for the stage of bit blunting and replace the bit when considerable
decrease of efficiency is observed.
ACCESSORIES
• SDS-Plus twist drill bits for concrete Ø6 to Ø32 mm. We recommend operation
with Ø10 to Ø28 drill bits, for the optimum operation the machine is designed for.
• SDS-max core cutters up to Ø68 mm
• SDS-max point chisels up to 400 mm long
• SDS-max flat chisels up to 40 mm wide
▪ SDS-max groove chisel up to 20 mm wide
WARNING: We recommend using these accessories or attachments when
operating your power tool. The use of any other accessories or attachments might
present a risk of injury. Only use accessory or attachment for its stated purpose.
If you need any assistance for more details regarding these accessories, ask your
local STATUS service centre.
MAINTENANCE
WARNING: Always ensure that the tool is switched off and unplugged before
attempting to perform inspection or maintenance.
General inspection
Regularly inspect all fasteners and ensure they are properly tightened. Should any
of the screws be loose, retighten it immediately to avoid hazards.
If the replacement of the supply cord is necessary, this has to be done by the manu-
facturer or his agent in order to avoid a safety hazard.
Cleaning
For safe operation always keep the machine and its ventilation slots clean.
Regularly check to see if any dust or foreign matter has entered the ventilation slots
and the grills around the switches. Use a soft brush and/or air jet to remove any
accumulated dust. Wear safety glasses to protect your eyes whilst cleaning.
Exterior plastic parts may be cleaned with a damp cloth and mild detergent if
necessary.
EN
) and fixed
8
6. TECHNICAL SPECIFICATIONS
7. CE DECLARATION OF CONFORMITY
) WARNING: Never use alcohol, petrol or other cleaning agent.
Never use caustic agents to clean plastic parts.
WARNING: Water must never come into contact with the tool.
IMPORTANT! To assure product safety and reliability, repairs, maintenance and
adjustment (including brush inspection and replacement) should be performed by
certified service centres or other qualified service organisations, always using
genuine replacement parts.
Built-in dust protection. The protective ring (1) preserves the tool socket from dirt
during operation. While inserting the tool, take care that you do not damage the pro-
tective ring.
WARNING: Replace a damaged protective ring immediately!
To replace the protective ring (1), pull back the locking socket (2). Grasp the protec-
tive ring and pull it strongly slantwise forward. Place a new protective ring onto the
spindle and press it hard.
TECHNICAL SPECIFICATIONS
Мodel
Voltage 230 - 240V 50Hz
Power input
No load speed (max) 0 - 800 RPM
Max. impact rate 4400/min
Impact energy
Noise emission (EN 60704):
A-weighted sound pressure level LpA
A-weighted sound power level LwA
Vibration emission value
a , :10,66 m/s², K :1,5 m/s², a
h HD HD
ACCESSORIES
Plastic case, auxiliary handle, depth gauge, manual, packing.
CE DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product fulfils all the relevant
provisions of the following directives and the harmonized standards:
20 0642 / /Е G,2006/42/EC,EMV 2004/108/EG,EMC 2004/108/EC,RoHS 2011/65/EU
EN 60745-1:2009+A11:2010, EN 60745-2-6:2010,
EK9-BE-87:2014, EK9-BE-88:2014,
EN 55014-1:2006/+A1:2009/+A2:2011, EN 55014-2:1997/+A1:2010/+A2:2008,
EN 61000-3-2:2014, EN 61000-3-3:2013.
The technical documentation kept by the manufacturer:
STATUS ITALIA S.R.L., via Aldo Moro, 14/A, 36060 - Pianezze (VI), ITALY
MPR45 Capacity in concrete:
- twist drill bit
1050W - core cutter
Tool holder
Weight (EPTA 01/2003)
6 J Protection class (EN 60745-1)
90 dB(A), KpA:3dB
106 dB(A), KpA:3dB
, :10,75 m/s², K :1,5 m/s²
h CHeq CHeq
Caron Giacinto
STATUS ITALIA S.R.L.
9
32 mm
68 mm
SDS-Plus
5,1 kg
II
Director
EN