Werbung
Verfügbare Sprachen
Verfügbare Sprachen
80320 Disinfectant stand
80310
for Euro dispenser
Please read these assembly instructions carefully!
TECHNICAL DATA
STAND
- Total height:
1280 mm
- Height support:
820 mm
- Round base:
ø 275 x 41 mm
- Base tube:
ø 20 x 800 mm
MATERIAL
- Round base:
steel, galvanized, PA, TPE
- Base tube:
steel
SURFACE
pure white, powder-coated
WEIGHT
2.8 kg
DISINFECTANT HOLDER
- Mounting hole patterns for Euro dispensers:
-
a. 350/500 ml:
40 x 169 mm
-
b. 1000 ml:
40 x 203 mm
- drip cup:
ø 70 x 47 mm
MATERIAL
- Bottle holder:
steel, polyamide
- Thread:
steel, brass, zinc
SURFACE
pure white, powder-coated
WEIGHT
1.4 kg
SAFETY INSTRUCTIONS
The safety of the stand depends on the:
ROUND BASE
Handle with care due to the load, do not drop
(crushing hazard).
MOUNTING
Ensure that all screw connection are tight.
SURFACE
Only use the stand on suitable, i.e. level and
stable floors.
LOAD
Only for suitable Euro dispenser (350/500/1000ml);
see above TECHNICAL DATA.
SURROUNDINGS
Negative external influences (knocks, dragging around,
vibrations, wind etc.) must be avoided.
HANDLING
When changing the direction of the dispenser bottle
always turn the entire stand. Never loosen the thread 3
of the bottle holder.
INSTALLATION INSTRUCTIONS
STAND
1 Place the round base (with rubber insert) on the floor,
2 screw the base pipe with the external thread into
2
the base plate as far as it will go.
DISINFECTANT HOLDER
3 Screw in the threaded bolt of the dispenser holder into
3
the base tube as far as it will go.
4 The drip cup can be removed for cleaning purposes.
4
Subsequently press the drip cup from above back
4
into the holder.
EURO DISPENSER (not included in delivery)
5 Euro dispensers (various manufacturers) generally have
5
the following mounting hole patterns:
5
- 3 x ø 5 mm, distance: 40 x 169 mm (350/500 ml)
5
- 3 x ø 5 mm, distance: 40 x 203 mm (1000 ml)
5
NOTE - Do not use dowels and screws included by the
5
manufacturer of the dispenser because they are meant
5
for direct wall mounting - but rather:
6 Fasten the Euro dispenser back panel with:
6
- 3 x screws M5 x 15 mm, 3 x washers ø 5 mm
6
- 3 x lock nuts M5 (DIN985).
7 Mount the dispenser housing as described in the
7
manufacturer's instructions.
D. DISINFECTANT BOTTLE (not included in delivery)
8 Place the disinfectant bottle as indicated in the
8
Euro dispenser manufacturer's instructions.
INFORMATION
NOTE: Stand and dispenser holder are not
NOTE:
medically certified product.
- Negative effects of the disinfectant on the products
-
(surfaces, material) are not known to us.
- Nevertheless, we recommend to always remove possible
-
residues of the disinfectant in order to avoid possible
-
damage and to enjoy the product as long as possible.
- For cleaning purposes use a slightly damp cloth and
-
a non-abrasive cleaning agent.
Disinfectant is not included in the scope of delivery.
Total height
DISINFECTANT
HOLDER
Support
height in
assembled
condition
STAND
KÖNIG & MEYER GmbH & Co. KG
Kiesweg 2, 97877 Wertheim, www.k-m.de
80320-000-76 Rev.8a 03-79-903-00 5/20
Werbung
