Inhaltsverzeichnis
Werbung
Teach-in Parameters
Index
Parameter
Lenght
(dec)
Object Name
0x003A (58)
TI Select
1 octet
0x003B (59)
TI Result
1 octet
2 octets
0x003C (60)
SSC1 Param
2 octets
1 octet
1 octet
0x003D (61)
SSC1 Config
2 octets
2 octets
0x003E (62)
SSC2 Param
2 octets
1 octet
1 octet
0x003F (63)
SSC2 Config
2 octets
0x0066 (102)
Adjustment mode
1 octet
Device Specific Parameters
Index
Parameter
Lenght
(dec)
Object Name
1 octet
0x0048 (72)
Delay Settings
4 octets
1 octet
0x00B4 (180)
Output type
1 octet
The No Output configured in Push Pull mode with an NPN load does not reactivate after a short circuit condition. Remove the short circuit condition and cycle power to the sensor.
(1)
Subindex
Value/Range
(offset)
0x00 = SSC1 (default, C/Q pin and DO
pin)
Teach-in State
1(0)
2(4)
Flag SP1 TP1
3(5)
Flag SP2 TP1
1(16)
0-4095
2(0)
Not used
1(24)
0x00: High Active (default C01)
0x01: Low Active (default B01, T01)
2(16)
0x01: Single Point (default)
Not used (M03)
3(0)
0 ..10 Hysteresis (W03)
0 - 1 Hysteresis (Trimmer models)
1(16)
0-4095
2(0)
Non used
1(24)
0x00: High Active (default B01, T01)
0x01: Low Active (default C01)
2(16)
0x01: Single Point (default)
Not used (M03)
3(0)
0 ..10 Hysteresis (W03)
0 - 1 Hysteresis (Trimmer models)
0x00 = manual (default)
0x01 = IO-Link
Subindex
Value/Range
Description
(offset)
0 = no delay (default)
0x2 = Delay ON
1(32)
0x3 = One Shot
Select Delay mode (ON / OFF/ ONE SHOT)
0x4 = Delay OFF
2(0)
0...(2^32)-1
Delay value =
0x01 = PNP (default)
0x03 = Push Pull
(1)
1(8)
Output type of C/Q pin when in SIO mode
0x01 = PNP (default)
2(0)
Output type of DO pin
0x02 = NPN
0x03 = Push Pull
Description
Selection for Teach-in channel (volatile)
See IO-Link Smart Sensor Profile
Normalized distance (M03) / Switching threshold (W03) /
Trimmer value (sensitivity adjustment) (Trimmer models)
C/Q pin configuration
Normalized distance
DO pin configuration
Status of trimmer regulation (manual/IO-Link) (B01, C01, T01)
Delay [ms] *1000 / 141 (M03)
Delay [ms] *1000 / 45 (W03)
Delay [ms] *1000 / 157 (T01/C01/B01 LED emission)
Delay [ms] *1000 / 67 (C01 Laser)
Delay [ms] *1000 / 70 (B01 Laser)
Data Type
Access*
Remark
C/Q and DO outputs are antivalent.
UIntegerT
R/W
Teach SSC1 equals to teach SSC2
UIntegerT4
BooleanT
RO
BooleanT
UIntegerT
R/W
Saved in non-volatile memory
UIntegerT
UIntegerT
R/W
Saved in non-volatile memory
UIntegerT
UIntegerT
R/W
Saved in non-volatile memory
UIntegerT
UIntegerT
R/W
Saved in non-volatile memory
UIntegerT
BooleanT
R/W
Data Type
Access*
Remark
UIntegerT
R/W
Saved in non-volatile memory
UIntegerT
R/W
UIntegerT
R/W
Saved in non-volatile memory
UIntegerT
R/W
*RO = read only, WO = write only, R/W = read/write
Werbung
Inhaltsverzeichnis
