Ceag GHG 514 Betriebsanleitung Seite 19

1x hub M40 / 1/4" NPT
+ 1x blanking plug M40
Downloaded from www.Manualslib.com
Annex to operating instructions
Plug and socket system 60A, GHG 514
2
Wall socket
instructions GHG 510 7003 P0001.
The GHG 514 plugs and sockets are not
suitable for Zone 0 hazardous areas.
For installation only by qualified
electrician in accordance with the Natio-
nal Electric Code, Canadian Electric Code,
applicable local codes and the
instructions.
Select properwire size and type for load
and application. Refer to National Electric
Code, Article 400, for wire information.
The temperature class and explosion
group marked on the apparatus shall be
observed.
The operations must be carried out by
electrical suitably trained in hazardous
area with knowledge of increased safty
explosion protection
IEC 60079-14.
Modifications to the plugs and sockets or
changes of their design are not permitted.
They shall be used for their intended
purpose and in perfect and clean
condition.
For replacement and repair only genuine
COOPER CROUSE-HINDS / CEAG spare
parts shall be used.
Repairs that affect the explosion
protection, may only be carried out by
COOPER CROUSE-HINDS / CEAG or a
qualified electrician in compliance with
the respective national regulations.
Prior to taking the plugs and sockets into
operation, they will have to be checked in
accordance with the instruction as per
section 6.
The sockets may only be used with the
associated COOPER CROUSE-HINDS /
CEAG plugs in undamaged condition.
The interlocking switch of the socket is
mechanically secured by means of spring-
loaded locking pins, and cannot be
connected without plug.
Before the initial operation, any foreign
matter will have to be removed from the
inside of the plugs and sockets.
Observe the national safety rules and
regulations for prevention of accidents as
well as the safety instructions included in
these operating instructions and set in
italics the same as this text!
manuals search engine
Safety instructions
Attention! These "Annex for
operating instructions"
GHG 510 7003 P0004 is only for
use with the original operating
3 Conformity with standards
The plugs and sockets meet the
requirements of the following standards:
C22.2 No.0-M91
Canadian Electrical
Code Part II
C22.2 No.182.1-07
Plugs and
Receptacles
C22.2 No 60079-0-07 Electr. App. for Expl.
Gas Atmosp.- Part 0: General Requirements.
C22.2 No 60079-1-07 Electr. App. for Expl.
Gas Atmosp.- Part 1: Flameproof Enclosure
"d".
CSA No 60079-7-03 Electr. App. for Expl.
Gas Atmosp.- Part 7: Increased Safety "e".
CSA No 61241-1-1-03 Electr. App.
protected by enclosures and surface
limitation - Specification for apparatus.
UL 1682-07 Plugs and Receptacles.
UL 1686-07 Pin and Sleeve Configurations.
UL 60079-0 Electr. App. for Expl. Gas
Atmosp.- Part 0: General Requirements.
UL 60079-1 Electr. App. for Expl. Gas
Atmosp.- Part 1: Flameproof Enclosure "d".
UL 60079-7 Electr. App. for Expl. Gas
Atmosp.- Part 7: Increased Safety "e".
UL 1203 Explosion-Proof and Dust
Ignition-Proof Electrical Equipment for use in
Hazardous (Classified) Locations.
4 Field of application
The plugs and sockets GHG 514 are suitable
for use in:
Class I, Zone 1
Class I, Division 2 - Groups A, B, C and D
Class II,Division 1 - Groups E,F and G (cUL)!
The enclosure materials employed, including
the exterior metal parts, are made of high-
quality materials which ensure a corrosion
protection and resistance to chemical
substances corresponding to the
requirements in a "normal industrial
atmosphere":
- impact resistant polyamide
- glass-fibre reinforced polyester
- special steel AISI 316 L
In case of use in an extremely aggresive
atmosphere, please refer to manufacturer
Cooper Crouse-Hinds GmbH
3 3 3 3 3