Daspi R1RC Bedienungsanleitung Seite 7

EN
DESCRIPTION
433.92 Mhz radio receiver, with 1,2 or 4 channels for rolling-code
transmitters. Available in the swift latch version "R" (for pre-set
stations) or in the outdoor version "RE" with terminals and plastic
casing. 250 radio controls memory capacity with different coding.
Suggestions for the installation: in order to obtain maximum
performance it is advisable to install the receiver far from sources
of noise and the aerial far from metal masses; should it be necessary
to install multiple receivers within the same area, these will have to
be at a distance of at least 1mt. from each other. Before connecting
the receiver check that the supply voltage corresponds, and that the
relay contacts capacity is suitable for the load that has to be applied.
Possibility of selecting three different types of operation per channel:
Monostable (default), the relay is activated upon the command and
deactivated automatically. Bistable, the relay is activated and remains
active until a further command is received. Timed, the relay remains
active for the time set.
MONOSTABLE PROGRAMMING (NORMALLY USED)
After having powered the receiver the green LED switches on for
1 second to signal the passing of the initial memory test. Should
this not occur, and the orange LED switches on instead, contact the
customer assistance service. Entry into programming mode takes
place by pressing buttons B1-B2-B3-B4. Each button associates the
remote control to the relative channel: B1=channel 1; B2=channel 2;
B3=channel 3; B4=channel 4. Press the button on the receiver relative
to the channel to which it is intended to associate the remote control:
the green LED switches on. Press the button of the remote control to
be stored the green LED flashes 3 times to indicate that the storing has
taken place. After having pressed the button on the receiver there is a
10-second timeout for completing the operation.
PROGRAMMING OF THE RELAY OUTPUTS (BISTABLE-TIMED)
To enter the channel (B1-B2-B3-B4) configuration stage, press twice
the button associated to the channel on the receiver. Upon the first
pressing of the button, the green LED switches on (storing of the code);
on the second pressing the green LED starts flashing, at this point,
for all channels, the programming takes place only by means of the
B1 button. Monostable mode: press button "B1"once , the green LED
switches on permanently, after 5 seconds it flashes once. Bistable
mode: press the "B1" button twice; upon the second command, the
green LED turns red and after 5 seconds it flashes once. Timed mode:
press the "B1" button three times: upon the third command the red
LED turns orange and after 5 seconds switches off. At this point the
red LED indicating the seconds starts flashing: each flash counts as
1 second for the timing to be set. After the required time calculated
in seconds has lapsed, press button "B1": the LED turns green and
starts flashing, indicating the minutes. Each flash counts as 1 minute in
the timing to be set. After the required time calculated in minutes has
lapsed, press button "B1" again: the flashing of the green LED stops
and a flash of the orange LED will confirm the end of the time setting.
Example 1: to set a timing of 2 minutes and 20 seconds on the second
channel, press button "B2" twice, the green LED flashes, press button
"B1" 3 times and the orange LED switches on; after five seconds the
orange LED switches off and the red LED starts flashing (with each
flashing indicating one second); after 20 flashes press button "B1"
once (halting the timing of the seconds); after three seconds the
green led starts flashing, (each flash indicating one minute); after 2
flashes press button "B1" (stopping the minutes timing and quitting
the programming); an orange flash indicates that the programming has
been quitted. Example 2: to set 20 seconds on the second channel,
press button "B2" twice, the green LED flashes, press button "B1" 3
times (the orange LED switches on), after five seconds the orange LED
switches off and the red LED starts flashing, (each flash indicating one
second); after 20 flashes press button "B1" twice (I halt the timing and
quit the procedure); an orange flash indicates that the programming
has been quitted.
REMOTE STORING OF A NEW RADIO RECEIVER
This function is used to store a new remote control without having to
open the casing of the receiver or to remove the operator protection
cover, as for example when remote control units need to be added to
an existing system.
For ease of understanding, the already existing remote control stored
in the receiver's memory will be called "A" and the new remote control
to be stored will be called "B".
Press and hold down channels 1 and 2 simultaneously on remote
control "A" for more than 5 seconds. The memory of the receiver is
at this point ready to accept a new code (if the receiver is visible, the
two-colour LED can be seen to flash red-green). Press the button on
remote control "A" corresponding to the channel on which the new
remote control "B" is to be stored. If for example, a new remote control
"B" is to be stored on channel 2 of the receiver, proceed as follows:
simultaneously press buttons 1 and 2 of remote control "A" for over
5 seconds, release, press button 2 on the same remote control, then
press the button on remote control "B" that is to be associated with
that channel
PROCEDURE FOR THE CANCELLATION OF A CODE
Keep button "B2" pressed for more than 5 seconds: on pressing the
button the green LED switches on and after 5 seconds the orange
LED lights up. At this point the cancellation mode is the same as the
learning mode: on the pressing of the radio control button, the LED
flashes 3 times to indicate cancellation of the code. After pressing the
button on the receiver a 10-second timeout controls the completion
of the operation. If a code is associated with multiple channels it
will be eliminated from all associations. If the code received is found
in memory, the orange LED will flash 3 times, otherwise it simply
switches off.
MEMORY CANCELLATION
Keep button "B2" pressed for more than 10 seconds. Upon pressing
the button, the green LED switches on (code storing stage); after 5
seconds the orange LED lights up (code cancellation stage); after
10 seconds, as confirmation of the memory cancellation, the orange
LED flashes 3 times. NB: after the memory cancellation, all radio
controls are cancelled and all the outputs are returned to the default
monostable function