Troubleshooting; Technical Data - Niko 310-0390X Bedienungsanleitung

310-0390X
4.3.2. With memory
With memory function, the rotary button operates as follows:
- Press briefly : off / on at previous dim level
Please note: The dimmer is never separated from the mains voltage. All components remain connected to the
power, even when the lamp is switched off.
4.4. Memory function
4.4.1. Switching the memory function on and off
The dimmer is supplied with the de memory function disabled. To activate the memory function, dim up to the
maximum light level and then hold the control button down for 10 sec. After 10 sec. the light dims from 100% to
a lower light level to indicate that the memory function has been switched on. After this change in light intensity,
immediately release the control button.
Repeat the procedure to deactivate the memory function.
This function, and the last set light level, is stored in a non-volatile memory; i.e. they will not be lost in the event
of a power failure. With the memory function activated, the dimmer will switch on for the first time at a light level
chosen by the manufacturer. Thereafter, the dimmer switches on at the last set value.
4.4.2. LED profiles LED 3, LED 7 and LED 8 with memory function
The dimming profile has been made in such a way, that the dimmer is shortly switched on at < 50 % of the
light intensity, before changing into the memory setting.

5. TROUBLESHOOTING

Signals that are sent via the mains can interfere with the operation of the dimmer. This is not a defect.
Problem Cause
The feedback LED does not The mains voltage is disconnected.
flash red after the mains voltage
is switched on (note: this only
The wire is defect.
lasts 5 sec.)
No lamp has been placed or the lamp
is defect.
The dimmer is not working. The The minimal dimming level is set
feedback LED flashed red after too low.
switching on the mains voltage.
The dimming profile is wrong.
The dimmer switches off by The protection against thermal
itself. The feedback LED on the overload (temperature is too high)
dimmer flashes red. or short circuits has been activated.
The
wrong.
The lamp is flashing. The lamp is not dimmable.
The minimal dimming level is set
too low.
The dimming profile is wrong.
There is a PLC malfunction.
The lamp is not suitable.
The dimmer is defect.
The lamp cannot be switched There is current leakage.
off.
The lamp flashes once the Wrong profile (the LED lamp is highly
maximum intensity is reached capacitive)
and dimming profile LED 5 or
LED 7 is set.
The lamp is humming/makes The lamp is not suitable for phase
audible noise. control.
When I use the MIN DIM LEVEL The dimming profile is wrong.
button, I cannot switch the lamp
back on.
6
EN nv Niko sa Industriepark West 40, BE-9100 Sint-Niklaas, Belgium — tel. +32 3 778 90 00 — fax +32 3 777 71 20 — e-mail: support@niko.eu — www.niko.eu
Action
Connect the device to the mains
voltage.
Replace the wire.
Place or replace the lamp.
Increase the minimum dimming level
or use a profile with boost function
(LED 3, LED 7 or LED 8).
Choose another profile and adjust the
minimum dimming level.
Check if the lamp is dimmable. This
is shown on the packaging by the
following symbol:
Check whether the load is too high.
When doing this, keep in mind the
reactive power of ferromagnetic
transformers.
Check the temperature in the flush-
mounting box (max. 35 °C).
Check whether mixed loads are being
used.
dimming profile is For LED lamps, use the profiles in the
following order of preference:
- DEFAULT 1
- LED 4, LED 5, LED 6
- LED 7 or LED 8 (with boost function)
Check if the lamp is dimmable. This
is shown on the packaging by the
following symbol:
Increase the minimum dimming level
or use a profile with boost function
(LED 3, LED 7 or LED 8).
Choose another profile and adjust the
minimum dimming level.
Place a PLC filter (Ripple Control
Rejector)
Replace the lamp if it flashes during
dimming the light up and down.
Replace the dimmer.
Place a 'bypass' or bleeder over the
lamp.
Select dimming profile Default 1, LED 4
or LED 8.
Select dimming profile LED 5 or LED
7 (note: the lamp might begin to flash
at maximum light intensity because
the lamp is highly capacitive). In
that case, we recommend placing a
different lamp.
Select dimming profile LED 3, LED
7 or LED 8.

6. TECHNICAL DATA

power supply voltage 230 V AC ± 10%, 50 Hz
INSTALLATION flush-mounting box with flush-mounting depth of min. 40 mm
weight ± 70 g
own power consumption < 0.15 W
max. ambient temperature (Ta) see power consumption graph below
power consumption* Maximum power : see input load table 4.1.
depending on the ambient temperature
(see power consumption graph below)
max. wire diameter per connection 2 x 2.5 mm²
terminal
min. load 3 W
safety protections protection against thermal overload and short-circuit
max. distance between dimmer and the 75 m
push button
standards EN 60669-2-1
* The dimmable capacity decreases by 10 % per 5 °C once the ambient temperature of 35 °C is exceeded.
100%
95%
90%
85%
80%
75%
70%
65%
60%
55%
50%
0 10 20
Ambient temperature (°C)
By placing dimmers above one another in the wall, the temperature of the dimmers might increase more quickly,
making the table above applicable faster.
7. WARNINGS REGARDING INSTALLATION
• The installation should be carried out by a registered installer and in compliance with the applicable regulations.
• This user manual should be presented to the user. It should be included in the electrical installation file and it
should be passed on to any new owners. Additional copies are available on the Niko website or via the Niko
support service. The latest manual for this product is available on the Niko website at any time.
• During installation, the following should be taken into account (non-exhaustive list):
- the applicable laws, standards and regulations.
- the technology available at the time of installation.
- this user manual only states general regulations and should therefore be read within the scope of each
specific installation.
- the rules of proper workmanship.
This product complies with all of the relevant European guidelines and regulations. If applicable, you can find
the EU declaration of conformity regarding this product at www.niko.eu.
8. NIKO SUPPORT
Not sure? Or do you want to exchange a faulty product? Contact your wholesaler or the Niko support service:
• Belgium: +32 3 778 90 80
• The Netherlands: +31 880 15 96 10
Contact details and more information can be found on www.niko.eu Under the "Help and advice" section.
9. WARRANTY PROVISIONS
• The warranty period is four years from the date of delivery. The delivery date is the invoice date of purchase
of the product by the consumer. In the absence of an invoice, the date of production applies.
• The consumer is obliged to inform Niko in writing about the non-conformity within two months of noticing
the defect.
• In case of a non-conformity, the consumer only has the right to a product repair or replacement free of
charge, at Niko's discretion.
• Niko shall not be held liable for a defect or damage resulting from incorrect installation, improper or careless
use, incorrect operation, transformation of the product, maintenance that does not adhere to the maintenance
instructions or an external cause, such as damage due to moisture or overvoltage.
• The compulsory regulations of the national legislation concerning the sale of consumer goods and the
protection of the consumer in the countries where Niko sells, directly or via sister companies, subsidiaries,
chain stores, distributors, agents or permanent sales representatives, take priority over the above-mentioned
rules and regulations.
This product cannot be deposited in non-recyclable waste. Take your discarded product to a recycling centre or a recognised
collection point. Just like producers and importers, you too play an important role in the promotion of sorting, recycling and
reuse of waste electrical and electronic equipment. To finance the rubbish collection and waste treatment, the government
levies recycling charges in certain cases (included in the price of this product).
30 40 50
PM310-0390XR17392
60