Environmental Protection; Operating Instructions; Prepare The Machine; Preparing To Work - GGP ITALY BL 260 H Gebrauchsanweisung

it can cause no danger to persons and fasten it
firmly in place to avoid it from tipping over, which
may cause damage or fuel spillage.
F) ENVIRONMENTAL PROTECTION
Environmental protection should be a priority of
considerable importance when using the ma-
chine, for the benefit of both social coexistence
and the environment in which we live. Try not to
cause any disturbance to the surrounding area.
• S crupulously comply with local regulations
and provisions for the disposal of oils, petrol,
damaged parts or any elements which have a
strong impact on the environment; this waste
must not be disposed of as normal waste,
it must be separated and taken to specified
waste disposal centres where the material will
be recycled.
• S crupulously comply with local regulations
and provisions for the disposal of waste ma-
terials.
• A t the time of decommissioning, do not pollute
the environment.

OPERATING INSTRUCTIONS

NOTE - The images corresponding to the
references are found from page v of this
manual.

1. PREPARE THE MACHINE

The machine can be used as both a blower and
a vacuum collector; for both of these uses it is
necessa r y to correctly arrange the appropriate
accesso r ies included with the equipment.
WARNING! Unpacking and completing
the assembly should be done on a flat and
stable surface, with enough space for moving
the machine and its packaging, always mak­
ing use of suitable equipment.
1.1 USE AS A BLOWER (Fig. 1)
– R emove the screw (1) and its washers (2).
– A lign the first blower tube compartment
(3) with the protrusion (4) of the air outlet,
push the tube and turn it 90° clockwise, in or-
der to per m anently fix it in place.
– F ix the tube (3) to the air outlet using the
screw (1) and its washers (2).
– A lign the second blower tube compartment (5)
with the protrusion (6) of the first tube, push
the tube and turn it 90° clockwise, in order to
permanently fix it in place; now use the screw
(7) and relative washers to fasten the tube (5)
in place.
NOTE The machine is correctly as sembled when
the flat part of the blower chute is pointed towards
the ground.
1.2 USE AS A VACUUM COLLECTOR
(Fig. 2)
– R emove the screw (1) and its washers (2).
– A lign the housing of the tube fitting bag
(3) with the protrusion (4) of the air outlet,
push the tube and turn it 90° anticlockwise, in
or d er to permanently fix it in place.
NOTE The machine is correctly as sembled when
the tube's terminal chute is pointed downwards
and to the left of the ope rator.
– F ix the tube (3) to the air outlet using the
screw (1) and its washers (2).
– L oosen the knob (5) and open the protection
grille (6).
– A lign the first vacuum tube compartment
(7) with the protrusion (8) of the inlet, push
the tube and turn it 90° clockwise, in or d er to
permanently fix it in place.
– A lign the second vacuum tube compartment
(9) with the protrusion (10) of the first tube,
push the tube and turn it 90° clockwise, in or-
der to permanently fix it in place.
NOTE The machine is correctly as sembled when
the rounded part of the chute is pointed towards
the ground.
– I nsert the tube fitting end chute (3) in the spe-
cific bag (11) and close the opening with the
supplied Velcro strap (12).
– H ang the bag over your shoulder and adjust
height using the strap.

2. PREPARING TO WORK

2.1 CHECKING THE MACHINE

Before starting work please:
– c heck that all the screws on the machine are
tightly fastened;
– w hen used as a vacuum collector, make sure
the bag is integral, well-closed and that the
zipper works correctly;
– c heck that the air filter is clean;
– c heck that the handgrips are well fastened;
5