Safety Precautions; Environmental Protection Measures - EB TECHNOLOGY START S10 Bedienungsanleitung

2
Foreword
This manual provides all the specific information you need to fa-
miliarize yourself with and correctly operate your unit.
Read it very carefully when you purchase the instrument and
consult it whenever you have doubts regarding use and before
performing any maintenance operations.

Safety precautions

Using the unit improperly and performing repairs or modifications
personally will void the warranty.
Nologo declines any responsibility for damages due to inappro-
priate use of the product and due to any use other than the use
the product was designed for.
Nologo declines any responsibility for consequential damages
except civil liability for the products.
The automation is conformed to the european laws: EN 60204-1,
EN 12445, EN 12453
It is compulsory to be conformed to the automatic gates: EN
12453, EN 12445, EN 12978 and national laws.
The force of the door should be measured and adjusted accor-
ding the maximum values of the norm EN 12453.
Environmental protection
measures
Information regarding the environment for custom-
ers within the European Union. European Directive
EC 2002/96 requires that units bearing this symbol
on the unit and/or on the packaging be disposed of
separately from undifferentiated urban wastes.
The symbol indicates that the product must not be disposed of
with the normal household wastes. The owner is responsible
for disposing of this product and other electrical and electronic
equipment through specific waste collection facilities indicated
by the government or local public agencies. Correct disposal
and recycling help prevent any potentially negative impact on
the environment and human health. To receive more detailed
information regarding disposal of your unit, we recommend that
you contact the competent public agencies, the waste collec-
tion service or the shop where you purchased the product.
Piccol
Small dictionary
OLS Opening Limit Switch
CLS Closing Limit Switch
START START control
PEDESTRIAN Partial Opening
Vac
(alternate current)
Vdc (direct current)
NC Normally closed
NA o NO Normally open
Contatto pulito Isolated contact
Index chapter
1
Introduction
1.1
Description of the produc
1.2
Technical caracteristics
2
Premises
2.1
Preliminary checks
2.2
Type of cable
2.3
Installation
2.4
Notes of connections
2.5
Scheme of the control unit and electrical connections
3
Installation of the control unit
3.1
Connection of the POWER SUPPLY
3.2
Connections of the MOTORS
3.3
Connection of the ANTENNA
3.4
Power supply of the ACCESSORIES
3.5
Connection of the STOP
3.6
Connection of the COURTESY LIGHT
3.7
Connection of the SIGNAL LIGHT
3.8
Set up of the PRE-LIGHTING
3.9
Connection of the LIGHT
3.10
Connection of the LImIT SWITCHES
3.11
Connection of the START and PEDONALE
3.12
Connection of the PHOTO-BEAm A (only closing)
3.13
Conneciton of the PHOTOBEAm A with TEST
Connection of the PHOTOBEAm B
3.14
(when opening and closing)
3.15
Connection of the PHOTO-BEAm B with TEST
3.16
Connection of the NEW LOCK SYSTEM
3.17
Connection of the mECHANICAL EDGE
3.18
Connection of the motor with electro-magnetic bloc
3.19
Check of the connections
4
Functions and adjustment
4.1
Function
4.2
Activation of the OUTPUTS
4.3
Watch the tension of the BATTERIES
4.4
SPEED and SLOW DOWN of the motors
4.5
Level of the OBSTACLE DETECTION
4.6
Function of the OBSTACLE DETECTION
5
Installation of the radio receiver and remote controls
5.1
Cancellation of the MEMORY
5.2
Cancellation of a SINGLE CODE
5.3
Activation of the ROLLING CODE COUNTER
5.4
Memorization of the code of the REMOTE CONTROLS
Learning and programm of the working time with
6
START
6.1
Working time learning with START
Working time learning with START or
6.2
PARTIAL OPENING
7
RESET of the control unit with standard values
8
Table with all START FUNCTIONS of S10
9
CE declaration of conformity
3
4
5
6
7
8
9
10
11
12
13
14
15.
16
17
19
23