Werbung
Quicklinks
Thank you for purchasing our Audio-Visual Direct
Vielen Dank für den Kauf unseres Audio-Visual Direct
Merci d'avoir acheté un meuble Audio-Visual Direct
Standing Desk / Stehpult / Bureau Debout
Model #16035
Modell #16035
Modèle #16035
Audio-Visual Direct LLC
Sacramento, CA 95834
service@audio-visual-direct.com
2016 AUDIO-VISUAL DIRECT LLC.
Werbung
Inhaltszusammenfassung für avd 16035
- Seite 1 Thank you for purchasing our Audio-Visual Direct Vielen Dank für den Kauf unseres Audio-Visual Direct Merci d’avoir acheté un meuble Audio-Visual Direct Standing Desk / Stehpult / Bureau Debout Model #16035 Modell #16035 Modèle #16035 Audio-Visual Direct LLC Sacramento, CA 95834 service@audio-visual-direct.com...
- Seite 2 Parts List / Liste der Teile / Liste de pièces détachées H x 4 A x 2 B x 2 C x 2 D x 2 E x 1 F x 2 G x 2 I x 1 J x 1 K x 1 N x 4 P x 1...
- Seite 3 Step 1 / Schritt 1 / Étape 1 • Insert Wheels (H) into Base (A) and tighten with Allen Wrench (R) completely so the wheels are level. Insert Lower Leg (B) into Base (A) then connect with Long Screw (L) and tighten using Large (B).
- Seite 4 Step 2 / Schritt 2 / Étape 2 • Put Upper Leg (C) into Lower Leg (B). Separate Knob Bolt (M). Connect Knob (M2) and Bolt (M1) through the hole at the top of the Lower Leg (B), then tighten slightly. Do not fully tighten since you will need to adjust this later. •...
- Seite 5 Step 3 / Schritt 3 / Étape 3 • Insert Long Screw (L) through screw hole in Base (A) until screw extends fully through. Align screw hole from end of Bottom Cross Tube (F) to Long Screw (L) and screw until tight. Repeat with the other screw hole from Base (A) and Bottom Cross Tube (F).
- Seite 6 Step 4 / Schritt 4 / Étape 4 • Repeat Step 3, using Long Screw (L) to connect the other leg to the cross tubes. Connect the Support Tube (D) first since it is easier to balance, then connect the Base (A). •...
- Seite 7 Step 5 / Schritt 5 / Étape 5 • Fit Support Panel (E) between the two Upper Legs (C). Insert Short Screw (N) into Support Panel (E) and connect it to Upper Leg (C) and Support Tube (D) using a screwdriver. •...
- Seite 8 Step 6 / Schritt 6 / Étape 6 • Carefully lower product onto its back. Insert Medium Screw (O) through Bottom Cross Tube until screw extends fully through. Align Bottom Board (I) to screw from Bottom Cross Tube (F) and use Small Hex Wrench (Q) to tighten slightly.
- Seite 9 Step 7 / Schritt 7 / Étape 7 • Carefully raise product upright. Place Top Board (J) onto Support Tube (D). Raise one edge of Top Board (J) slightly and insert Medium Screw (O) upside down through the bottom hole of the Support Tube (D) below it.
- Seite 10 Step 8 / Schritt 8 / Étape 8 • Repeat the steps to install Middle Board (K) onto Support Tube (D). Place Middle Board (K) onto Support Tube (D). Raise one edge of Middle Board (K) slightly and insert Medium Screw (O) upside down through the bottom hole of the Support Tube (D) below it.
- Seite 11 Step 9 / Schritt 9 / Étape 9 • Your desk is now assembled. If the Top and Middle Boards are not level, untighten Knob Bolts (M2), adjust legs, and retighten to desired height. • Ihr Tisch ist nun zusammengebaut. Sind die Deck- und Mittelbretter nicht waagerecht, lösen Sie die Rändelschrauben (M2), justieren die Beine und ziehen die Schrauben anschließend auf der gewünschten Höhe fest.