Troubleshootings - FLASH HAGER 25312 Handbuch

Coding the transmitter with the
receiver
• Press the receiver's pushbutton for more
than 3 seconds. The indicator
flickering, release the pushbutton. The system is
in configuration mode.
• Press the Reset button during 3 seconds of
the transmitter.
The indicator button will stop flickering, at
the end of 5 secondes.
The transmitter/receiver link is now established.
• Set time.
For clearing all transmission/reception links:
• Press the receiver's pushbutton
than 10 seconds. The indicator
slowly, then more quickly.
• Press again the receiver's pushbutton
than 3 seconds. The indicator
flickering, all links have been cleared.
Adjusting the temperature set
Your thermostat controls 2 levels of temperatures:
• Comfort temperature: this is the temperature
level you want during the time you are present
(20°C for example).
• Reduced temperature: this is the temperature
you want during short absences or at night
(16°C for example).
We advise a difference of 4 °C (minimum) between
the Comfort and Reduced temperatures.
To change the Comfort temperature:
• In Auto mode, using + or – keys to modify the
set-point. Such modification is temporary (last
segment of bargraph flickers). On next program
step, the thermostat will operate on the usual
set-point.
• In Comfort mode, using + or
the set-point. Such modification is permanent.
To change the reduced temperature:
• In Auto mode, using + or – keys to modify the
set-point. Such modification is temporary (last
segment of bargraph flickers). On next program
step, the thermostat will operate on the usual
set-point.
• In Reduced mode, using + or
the set-point. Such modification is permanent.
The Comfort and Reduced temperatures can
be set from +5°C to +30°C in steps of 0.5°C.
When you adjust the Comfort and Reduced,
finished, after 5 seconds the thermostat automa-
tically displays the ambient temperature.
The current set temperature is permanently
displayed on the bargraph.
In the case of a temperature set-point, the last
segment of the bargraph flickers.
Programmation
To programme your heating you have available 3
prerecorded and modifiable programs: P1, P2 and
P3:
• P1: Comfort from 6h00 to 23h00.
Reduced from 23h00 to 6h00.
light will start
• P2: Comfort from 6h00 to 8h30
and from 17h30 to 23h00.
Reduced from 8h30 to 17h30
and from 23h00 to 6h00.
for more
light flickers
• P3: Comfort from 6h00 to 8h30, from 11h00 to
more
14h00 and from 17h30 to 23h00.
l
ight stops
Reduced from 8h30 to 11h30, from 14h00
to 17h30 and from 23h00 to 6h00.
• The first programming time schedule appears and
flickers. The cursor
cates the start time of a Comfort temperature
cycle.
• Scroll the various programming schedules by
pressing the
• When the cursor
it indicates the start time of a Reduced
temperature cycle.
• When the schedule of the last cycle is confirmed
using the
mode and displays the room temperature.
• Using keys
– keys to modify
cycle as required (maintain key down for a
longer time to make minutes scroll faster).
In Auto mode the thermostat manages auto-
matically the desired temperature (Comfort or
Reduced) according to the program set.
On startup, P1 program is active in Auto.
To select the desired program:
• In Auto mode, press
desired program (P1, P2 or P3).
– keys to modify
• The displayed program flickers (for example P1).
OK
• Press
Permanent override
This mode transforms the appliance into a simple
electronic thermostat.
It no longer takes the timed program into
account.
• Press the
pointer
or Reduced) as you choose.
• To change the Confort or Réduit, use the
and – keys.
• The set temperature is displayed instead of the
ambient temperature and flashes, then the
thermostat returns to display of the ambient
temperature.
6h 23h
6h 8h30 17h30 23h
6h 8h30 11h30 14h 17h30 23h
under the symbol
OK key repeatedly.
is under the symbol
OK key, the thermostat is set to Auto
+ or –, modify the start time of each
Prog key to display the
to confirm.
Mode key and position the operating
, under the symbol or (Comfort
4
Temporary override
This mode allows to modify the temperature set-
point temporarily during a program step.
• In Auto mode, press the
the temperature set-point.
• The last segment of the bargraph then flickers
until the next program step.
On the next program step, the defined temperature
set-points are again active.

Troubleshootings

• The heating does not start:
- receiver's power supply is cut off (the
indicator light is off). Check fuse and circuit
breaker.
- re-install receiver.
• The system does not start or does not
stop:
- the receiver or transmitter is disturbed by
radio transmission (radio ham, TV monitor,
cellular phone re-transmitter, etc.): attempt to
remove the source of disturbance.
- Receiver is outside of transmitter's range, move
transmitter closer to receiver.
In case of persistent problem, call on your
electrician.
Technical specifications
Supply: 2 batteries type 1,5V LR03
Lifetime:
Power reserve:
Transmission frequency:
Transmitter duty cycle:
Range of setting of Comfort and Reduced
temperatures:
indi-
Range of display of ambient temperature;
Transmission distance: 100 metres in a clear field
Operating temperature:
Storage temperature:
,
Hygrometry:
Degree protection:
Class Insulation:
Dimensions:
IK:
Standards: NFC – 73251, NF EN 60730-1,
EN 300 220-1 V2.1.1, EN 300 220-2 V2.1.1
Made in France
Usable in all Europe and Switzerland
+
+ or – keys to modify
about 1 year
max. 20 sec.
433.92 Mhz
10%
5°C to 30°C
0°C to 40°C
0°C to +40°C
-20°C to +60°C
90% max to 25°C
IP 31
III
120 x 80 x 35 mm
04