User Manual; Package Contents; Bluetooth ® Connection - fontastic PRIME MESU Bedienungsanleitung

GB

User Manual

Thanks for choosing the MESU wireless speaker table. The sophisticated 2 x 12-Watt speaker table plays your audio
files in the best quality. Spoil your ears with full, powerful tones and enjoy the elegant design, which goes well in all
styles of home and turns every room into your personal feel-good zone. Please read the handbook thoroughly before
use and store it in a safe place for future reference.
ATTENTION
1. The maximum load-bearing capacity of the table is 5 kg. This must not be exceeded.
2. This product may not be used as a seat, either by adults or children.
3. Only use the original power supply for charging. Otherwise, the speaker might become damaged, charge
slowly or not charge at all. In extreme cases it could lead to irreparable damage.

Package Contents:

1 x Speaker table
1 x Power Supply
If any of the above pieces are missing, package the product and send it back to your dealer.
Assembly instructions:
1. Carefully place the speaker table upside down on a clean, level surface.
If necessary, remove the tabletop first.
2. Place the table legs in the recesses on the underside of the device.
Fix each of the legs with 4 screws.
3. Tighten the screws using the Allen key provided.
Device overview
Front panel
1 2 3 4 5 6
7
Connections
8 11
9
10 12
13
1
3 x Table legs 12 x Screws
1 x AUX Cable 1 x Allen key
1. On/off / TWS
2. Bluetooth / USB / AUX mode LED indicator
3. Start / pause / telephone
4. Volume-
5. TWS mode LED indicator
6. Volume+
7. Microphone
8. USB playback port
9. AUX audio socket
10. Charging LED
11. USB charging port: 5V 1A
12. Reset
13. Power inlet
Tabletop
14. Removable tabletop
14 15
15. Area for wireless charging
Getting started
Charging the battery
MESU is equipped with two internal, rechargeable lithium ion batteries, which also serve as a power bank.
As a result, MESU can also work without a direct power supply and can be used to charge external devices.
When the battery charge is low an audible signal sounds. If this happens, charge the speaker. To do this, plug the
provided power supply into a free, easy-to-access socket and connect it to the power inlet (13) on the back of the
speaker. The red LED (10) lights up while the device is charging and goes out once the device is fully charged.
Please note: charge the speaker for at least 2 hours before initial operation.
Switching on/off
To switch on press and hold the multifunction button
An audible signal indicates that the device has switched on. The device is in Bluetooth
To switch off press and hold the multifunction button
indicates that the device is switching off.
Bluetooth ® Connection
The speaker must be connected to a Bluetooth ® device before it can be used. This is a two-step process: one step is
performed with the speaker and the other with the Bluetooth
Please note: different mobile telephones use different pairing methods.
1. Switch on the speaker. Bluetooth mode starts automatically, the blue LED (2) slowly flashes.
®
2. Search for Bluetooth
® audio devices using the device from which you want to play audio.
3. The searching device indicates that it has found the "MESU" speaker. Confirm the connection if necessary.
A successful connection is confirmed with an audible signal. The blue LED (2) lights up permanently.
Music playback
Music control
To play or stop music playback, briefly press the multifunction button
To skip to the next track, press and hold the Volume+ button.
To skip to the previous track, press and hold the Volume- button.
AUX-in socket
You have the option to play your music via the AUX-in socket, allowing even non-Bluetooth
to be connected without problem.
Connect your playback device to the 3.5 mm AUX socket (9) on the back of the speaker using the AUX cable.
The speaker automatically switches to AUX mode and Bluetooth
Please note: After pulling out the 3.5 mm jack, the speaker will automatically switch back to Bluetooth
USB playback
Plug the USB storage device into the USB playback port (8). Start playback by pressing the
To switch to the next track briefly press the + button (6). To switch to the previous track briefly press the - button (4).
(1) for approx. 2 seconds.
mode by default.
®
(1) for approx. 2 seconds. An audible signal
device from which you want to send the audio data.
®
(3).
devices
®
mode is deactivated.
®
mode.
®
button (3).
GB
2