Basic Operations; Menu Settings - Mitsubishi Electric DX-TL2500E Kurzanleitung

Basic Operations

Multiplexer functions
Buttons on the front of the unit can be used to perform
some of the multiplexer functions.
Multiplexer buttons
2. SPLIT/SEQUENCE buttons
SPLIT/
SEQUENCE
ZOOM
0
3. ZOOM button
1. Camera number buttons (1 to 16)
Video images of cameras connected to CAMERA IN termi-
nals 1 to 16 on the rear of the unit are displayed.
By pressing a camera number button, video im-
ages can be displayed even if the camera is not set
for recording.
2. SPLIT/SEQUENCE button
The screen switches in order of SPLIT16, 2 types of SPLIT9
SCREEN SETTING (a, b), 4 types of SPLIT4 SCREEN
SETTING (a, b, c and d), SPLIT9 SEQUENTIAL, SPLIT4
SEQUENTIAL, and SINGLE SEQUENTIAL set in the <MPX
DISPLAY SETTINGS> screen (SEQUENTIAL display is
skipped during playback).
Pressing the OUTPUT B button on the front of
this unit can switch the operation of camera number
buttons and the SPLIT/SEQUENCE button to the
screen of the monitor connected to the OUTPUT B
connector. Pressing the OUTPUT A button can
switch to the screen of the monitor connected to the
OUTPUT A connector.
3. ZOOM button
When this button is pressed during single screen display,
magnification 100% screen appears and the magnification
centre point (X) is displayed at the centre. Pressing the
button again will switch the magnification to 200% and then
400%. By pressing the MOVE buttons, the magnified screen
can be moved vertically/horizontally with the centre point
as the axis.
When the ZOOM button is pressed, camera number
buttons 1 to 4 become the MOVE buttons.

Menu settings

The operational conditions of this unit can be set in the
menu screens according to use. Although the setting
method will differ slightly depending on the menu screen,
the basic setting method of using the JOG dial and SHUT-
TLE ring will remain the same. e.g. setting the display
mode.
SHUTTLE ring
•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• QUICK GUIDE
1. Camera number buttons (1 to 16)
16 16
MOVE buttons
JOG dial
Example : Set DISPLAY MODE to "3" ( default : "1" ).
1. Set the MAIN switch on the rear of the unit to ON. Press
the POWER button on the front after the ACCESS indicator
turns off.
• "SETTING UP..." appears on the screen and the unit is
booted.
• POWER button operation will not be accepted while the
ACCESS indicator is flashing. Press the POWER button after
the indicator turns off.
2. After boot-up, press the SET UP button inside the door on
the front of the unit.
• The <SETTINGS> screen appears.
<SETTINGS>
>>TIME DATE/DISPLAY SETTINGS
MPX DISPLAY SETTINGS
MOTION DETECTION SETTINGS
RECORD SETTINGS
TIMER PROGRAM SETTINGS
INITIAL SET UP/INFORMATION
QUICK SETTINGS
MEMO:
When the SET UP button is pressed and the
menu screen appears, the background darkens and
the displayed characters become easier to see.
3. Check to see that the cursor (>>) is positioned at "TIME
DATE/DISPLAY SETTINGS", and then turn the SHUTTLE ring
clockwise.
• The <TIME DATE/DISPLAY SETTINGS> screen appears.
<TIME DATE/DISPLAY SETTINGS>
>>TIME DATE ADJUST
DISPLAY MODE
CLOCK LOCATION SETTING
CAMERA DISPLAY
CAMERA TITLE/MEMO SETTING
DUPLEX MODE DISPLAY
<MODE 1>
01-01-2003 00:00:00
4. Turn the JOG dial to move the cursor to "DISPLAY MODE"
and turn the SHUTTLE ring clockwise.
• The background of the "DISPLAY MODE" setting turns red
and flashes.
When turning the JOG dial clockwise, the cursor
(>>) moves down. When turning counterclockwise,
the cursor (>>) moves up.
5. Turn the JOG dial to display "3".
• The display mode sample on the bottom of the screen
changes to <MODE 3>.
6. Turn the SHUTTLE ring clockwise.
• The setting is confirmed and flashing stops.
• To continue with other settings, repeat steps 4 and 5.
When turning the SHUTTLE ring counterclockwise
while the setting is flashing, the setting will return to
the previous setting.
To exit the screen, turn the SHUTTLE ring
counterclockwise.
1
NUMBER
BOTTOM
7