IPAS ComBridge BNG Bedien- Und Montageanweisung

ComBridge BNG
General Usage
The device is configured entirely with ETS which is one of the de-
vice's most outstanding features. No special knowledge about
BACnet is required for the commissioning. The objects configured
with ETS are "translated" into BACnet objects according to the fol-
lowing process:
The BACnet object instance number is identical to the object num-
ber of the ETS. Objects with a 1bit data type are translated into "bi-
nary" objects all others become "analogue" objects. The parameter
"Object Mode" (INPUT, OUTPUT, VALUE) completes the transfor-
mation to a BACnet object.
Delivery status:
IP-Adresse: 192.168.1.135
Subnet Mask: 255.255.255.0
Device types and accessories
At present the following device types are available:
ComBridge BNG: Best.Nr.: 3622-141-12
Scope of delivery
The following individual components are included in the delivery of the ComBridge BNG:
•
Complete device with connected bus connector
•
Operating and mounting instructions
Application programs
The following application programs are currently available:
3622-BacnetServer-01-0111
For application program functions, please see the Manual.
Installation advice
• The device is intended for interior installation in dry rooms.
• The prevailing safety rules must be heeded.
• The device must only be installed and commissioned by an accredited electrical engineer.
• Please follow country-specific safety and accident prevention rules as well as all current KNX guidelines.
• During the installation the device must be switched off.
• Do not open the device! Faulty devices must be returned to the manufacturer.
IPAS GmbH (Rev. 1.1)
Operating and mounting instructions
Order. Nr.: 3622-141-12
Page 1
ComBridge BNG
Technical Specifications
Power Supply
•
24 V DC
•
Consumption: 24V/40mA (ca. 1W)
•
In addition via KNX bus, SELV 24V
Connectors
•
Bus connector: KNX bus connector (black/red)
•
24 VDC connector (white/yellow)
•
Ethernet: RJ-45 plug 100MB/s
Control elements
•
Programming Button to toggle between normal and address-
ing mode
Display elements
•
LED red:Indicates normal/addressing mode
•
LNK-LED yellow: Signals device Ethernet readiness
•
ERR-LED red:Signals fault status
Ethernet
•
IP-connection via Ethernet, speed 100 Mbit / second
•
IP address allocation via DHCP service or fixed IP address
Mechanical data
•
Plastic ABS – V0
•
Dimensions REG casing 4TE:
Width: 72mm
Height: 55mm
Length: 86mm
•
Weight 150 g
•
Mounting: 35mm DIN rail
Location and function of the display and control elements
The device connectors as well as the programming button and programming LED that are required for commissioning are only accessible
in the distribution box when the cover is removed.
A1: DC 24 V bus connector terminal (yellow-
white)
A2: KNX bus connector terminal (black-red)
A3: Ethernet RJ45 socket
A4: KNX programming LED
A5: KNX learning button
A10: ErrorLED
A11: Ethernet Activity+Communication LED
IPAS GmbH (Rev. 1.1)
Operating and mounting instructions
Order. Nr.: 3622-141-12
Electrical safety
•
Pollution class (in accordance with EN60664-1):
•
Protection type (in accordance with EN 60529):
•
Protection class (according to IEC 1140)
•
Overvoltage category:
•
KNX Bus: Separated extra-low voltage SELV DC 24 V
EMC requirements
Complies with EN 50090-2-2 und EN 61000-6-2:2005,
EN 61000-6-3:2007
Environmental conditions
•
Weather resistence: EN 50090-2-2,
•
Environmental conditions during operation: -5°C to +45°C
•
Storage temperature: -25°C to +70°C
•
Rel. humidity (non condensing): 5 % to 93 %
Approbation
EIB/KNX registered
CE-Signage
According to EMC-Guidelines (Residential and commercial build-
ings), Low Voltage guidelines
A5 A4
A10
A11
A3
A1
A2
Page
2
IP20
I
III
2