Quick Start Guide; Hdmi Matrix - nedis VMAT3472AT Kurzanleitung

a

Quick start guide

HDMI Matrix

For more information see the extended manual
online: ned.is/vmat3472at
Intended use
This product is intended to connect up to 4 HDMI inputs with up to
2 HDMI outputs and switch between them.
The product also splits video and audio.
Any modification of the product may have consequences for safety,
warranty and proper functioning.
Main parts (image A)
1
HDMI Matrix
2
Remote control
Front panel (image B)
1
Power switch
2
Remote control sensor
3
HDMI input indicator LEDs
for HDMI output A
4
HDMI input indicator LEDs
for HDMI output B
5
Select button, to switch
HDMI input (1-4) to HDMI
output B
6
Select button, to switch
HDMI input (1-4) to HDMI
output A
Rear panel (image C)
1
RS-232 communication port
2
HDMI inputs (1-4)
3
HDMI outputs (A-B)
4
Optical digital output port
Remote control (image D)
1
Power button
2
Select HDMI input buttons
for HDMI output A
Safety instructions
- WARNING
• Do not use a damaged product.
• Only use the product as described in this manual.
•
Do not expose the product to direct sunlight, naked flames or
heat.
VMAT3472AT
3
5 VDC / 2 A Power adapter
7
Audio select button, to
switch between audio
output modes
8
5.1 CH audio channel
indicator LED
9
2.1 CH audio channel
indicator LED
10
Optical digital audio output
indicator LED
11
HDMI pass-through indicator
LED
12
Audio Return Channel (ARC)
indicator LED
5
L/R analog stereo audio
output port
6
Power supply port
3
Select HDMI input buttons
for HDMI output B
4 8
- Select audio output
mode buttons
•
Do not expose the product to water or moisture.
•
Place the product on a stable and flat surface.
•
Do not drop the product and avoid bumping.
• Do not open the product.
• Keep the product out of reach from children.
Installation
Connection diagram (image E)
• Connect HDMI input devices E
using a HDMI cable. A HDMI input device can be for example a
DVD player, a set top box or a game console.
•
For audio, the following connections are possible:
Audio L/R
Toslink (Optical)
HDMI pass-through Output
A / B
• Connect the HDMI output devices E
3
C
using a HDMI cable.
• Connect a RS-232 Equipped PC or Notebook E
1
port C . To make this connection use a RS-232 to USB cable
and a RS-232 female to 3 Pin Phoenix Connector. This
connection enables to send ASCII commands to the HDMI
1
splitter A
.
• Connect the power supply port C
the supplied DC 5 V, 2 A power adapter A
Switch HDMI inputs to a HDMI output
For the following options, use the remote control D
• Press the HDMI input buttons D
each HDMI output (A, B).
4
• SPDIF D : Enable or disable Optical Digital Audio output
(SPDIF).
8
• ARC D
: Enable or disable Audio Return Channel (ARC).
Use ARC if your HDMI output device is the audio source (for
example if your TV has a built-in tuner) and you want to return the
audio signal through the HDMI connection.
Note: make sure the used HDMI cable supports ARC.
5 5
• PASS D : Press D
input device to the HDMI outputs.
6 6
• 5.1 D : Press D
channel.
7 7
• 2.1 D : Press D
channel.
4
1
to the HDMI inputs C
Connect stereo audio
2
equipment E using a L/R
cable.
Connect Toslink supported
audio equipment E
Toslink cable.
Note: Toslink does not support
Dolby Digital plus.
You maybe need to change the
audio settings of your input
device.
Connect an audio receiver E
between your HDMI output
5
E and the HDMI splitter.
The audio receiver must
support a HDMI pass-through.
You will need 2 HDMI cables.
5
to the HDMI outputs
6
5
to a power outlet using
3
.
234
23
to select the input for
to send the audio from the selected
to set the audio output mode to 5.1
to set the audio output mode to 2.1
2
3
using
4
to the RS-232
: