Felisatti RF30/750 Bedienungsanleitung Seite 3

TECHNICAL DATA
Router/trimmer
Input power
No-load speed
Clip diameter
Approx. weight (without acces.)
The instructions contained in this manual must be strictly
followed, it should be carefully read and kept close at
hand to use when carrying out maintenance on the
indicated parts.
If the machine is used carefully and normal maintenance
is carried out, it will work well for a long time.
The functions and use of the tool you have bought shall
be only those described in this manual. Any other use
of the tool is strictly forbidden.
ILLUSTRATIONS
DESCRIPTION (See figures)
C Start-up switch (Fig.1)
D Clamping nut (Fig.1)
EQUIPMENT
- Clip,  1/8"
- Clip,  8 mm
- Fixed spanner 13 mm
- Fixed spanner 17 mm
- Operating instructions
- Safety instructions
- Warranty
SAFETY INSTRUCTIONS
 See "Safety Instructions" manual, supplied with this
instruction manual.
 For your personal safety, always connect the machine
to a mains supply protected by a differential and ther-
mal cutout switch, in accordance with regulations on
low-voltage wiring sitemaps.
 Do not pierce the motor housing as this could damage
the double insulation (use adhesive labels).
 Always unplug the machine before carrying out work
on it.
 Always stop the machine by switching it off, not by
unplugging it.
 WARNING! Before each use, inspect the plug and
lead. Should they need replacing, have this done by an
official service centre.
 Always keep the mains lead clear of the working range
of the machine.
 Only plug the machine in when it is switched off.
 Hold the machine firmly in both hands and in a stable
position.
 When working with the machine, always wear safety
goggles and ear protection. Other personal protection
equipment such as dust masks, gloves, helmet and
apron should be worn when necessary, along with non-
slip safety footwear. A dust mask is required when the
dust from the material deburred, such as paint or other
coating, is harmful. If in doubt, use safety equipment.
W
rpm
mm
kg
 Make sure the vents are free when working with dust. If
they require cleaning, first unplug the machine, do not
use metal objects and avoid damaging internal parts.
BEFORE USING THIS TOOL
Before using the tool, make sure the mains voltage is
correct: it must be the same as that on the specification
label. Machines with 230V can also be connected to a
220-V mains supply.
STARTING THE TOOL
Plug the machine in with the switch off.
Start the machine by turning the switch to position 1
("ON"). To switch off, do the same in reverse.
Fitting to the power tool (Mod. 90092.0000)
Remove the collet and the nut from the spindle of the
tool. Remove the 8 mm collet and fit the ⅛" one, fit the
⅛" bit and tighten the nut to fasten it. Fit accessory
90092.0000 by loosening screw A and fitting it in the
collar of the tool. Then tighten screw A to secure it.
DEPTH ADJUSTMENT
With the accessory securely fitted to the tool and the bit
in place, loosen the regulator set screw B, and move up
and down until the required depth is obtained. Tighten
the regulator set screw B to secure.
Warning: Bits should be specially cut for plaster or PVC.
ACCESSORIES
Accessories and their corresponding order number can
be found in our catalogues.
MAINTENANCE AND CARE
WARNING! Always unplug the machine before carrying
out work on it.
- Inspect the mounting screws: Regularly inspect all
the mounting screws and ensure they are firmly tight-
ened. Should any screw be loose, tighten it immedi-
ately. Failure to do so could put you at serious risk.
- Motor maintenance: Always take the greatest care
over this and make sure that the motor winding is not
damaged and does not become wet with oil or water.
- The vents should always be kept clean and free of
obstacles.
- Clean the machine thoroughly after each use. Blast the
motor regularly with compressed air.
- Check that the mains lead is in good condition. If it is
not, take it to an Official Service Centre to have it
replaced.
- Brush replacement: The brushes should be replaced
after 150 - 200 hours use or when they are less than
10 mm long. Have this done by an Official Service
Centre. We recommend that at every second change
of brushes, you take the machine to one of our Official
Service Centres for general cleaning and oiling.
RF30/750
750
27000
1/8"
1.9