Operation - ARESA AR-1301 Bedienungsanleitung

ENGLISH
Please read this instruction manual carefully before using the appliance. Save the instruction manual
Supply voltage: 220-240 V ~ 50 Hz
Power consumption: 45 W
• Read this manual carefully before operating the fan to avoid breakage during use. Incorrect handling can lead to damage to the product, cause material
damage or cause damage to the health of the user.
• Before initial start-up, check that the product specifications match the mains supply.
• The fan is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience or knowledge,
unless they are controlled or instructed about the use of the device by the person responsible for their safety.
• Do not leave the fan running unattended, especially if there are children near it.
• Avoid contact with moving parts of the fan. Do not push pencils or other objects through the protective grid of the operating fan.
• Do not operate the fan without the protective grid installed.
• The fan is designed to operate only in an upright position on a dry, hard, level surface.
• Do not use the fan if the cord or plug is damaged, or if the fan itself is damaged or defective. Take it to a service center. Do not repair it yourself.
• If the power cord is damaged, it must be replaced by a specialized service center to avoid danger.
• Do not place the fan near heat sources.
• Do not allow the power cord to touch sharp edges.
• Do not use the fan in places that are easily flammable.
• Always unplug the fan from the electrical outlet when it's not in use.
• Do not use accessories that are not included in the delivery.
• Do not use the fan outdoors or in a humid environment, especially in the close access to the bathtub, shower or swimming pool. To reduce the risk of
electric shock, do not operate the fan with wet hands.
• To prevent electric shock, do not immerse the fan in water or other liquids.
• When disconnecting the fan from the mains, hold the plug by hand, do not pull on the power cord. Do not twist or rewind the cord around the device.
• Do not use the fan for purposes other than those specified in the instruction manual.
• Use only for domestic purposes in accordance with this instruction manual. The fan is not suitable for industrial or commercial use.
• To avoid accidents, do not cover the fan!
The fan is delivered in disassembled state. Before starting the assembly, make sure that the complete set is delivered and the components are not damaged. Do not
connect the fan to the mains without fully assembling it.
Fix the stand on the base using the screws which are in the set. Remove the clip from the stand, put the decorative cover and lower it to the base. Slide the stand to the
desired length, place the clip to its place and tighten it. Place the motor unit to the stand abd fasten with a screw. Unscrew the fixing screws of the blades and the back
grill and remove them. Put the back protective grill on the shaft and secure with the screw. Install the blades on the shaft so that they reach the retainer on the shaft.
To lock the blades, tighten the screwfor blades fastening counterclockwise. Connect the front and back grills, and fasten them around the circumference of the hoop.
The fan is ready for operation.
The fan can work in 3 speed modes.
"1" - min speed rotation
"2" - medium speed rotation
"3" - max speed rotation
"0" - the fan is switched off
You can switch on the backlight using the button. There is a button for turning on the mode of rotation on the motor housing. If you press drown this button, the engine
with blades will begin to turn in different directions. To turn off the rotational mode, pull the button back. To turn off the fan, press "0" button.
Always unplug the fan when not in use.
The appliance and packing materials must be disposed with the least harm to the environment and in accordance with the rules for waste disposal
in your area.
TRANSPORTATION. Transportation of the device is necessary by any kind of covered transport with the application of cargo securing rules
ensuring preservation of the presentation of the product and / or packaging and its further safe operation. DO NOT expose the device to shock
loads during handling operations.
CLEANING. Before cleaning or servicing the fan, be sure to remove the plug from the outlet. Wipe the protective grid, blades, stand and base
with a damp soft cloth and then wipe dry. Do not use abrasives or solvents. The appliance must not be exposed to moisture and dust. Do not spray
the aerosol for cleaning into the ventilation slots of the motor housing.
STORAGE. The device must be stored indoors, in conditions that presume the preservation of the presentation of the product and its further safe
operation. Make sure that the appliance and all its accessories are completely dried, before storing it. To avoid damaging the cord, do not wind it
on the body.
This unit is designed to cool indoor air. For household use, not suitable for industrial use.
Important! The device purchased in the cold season, in order to avoid failure, must be kept at room
TECHNICAL SPECIFICATIONS
IMPORTANT SAFEGUARDS

OPERATION

OPERATION
RECYCLING
TRANSPORTATION, CLEANING AND STORAGE
WARRANTY TERMS
as you may require it in future.
temperature for at least four hours before being switched on.
Warranty period in the European Union - twenty four months