Location Of Controls; Power Connection; Getting Started - FIRST AUSTRIA FA-2419-3 Benutzerhandbuch

1
N
i
2
iNSTRUCTioN MANUAl
FM CloCk RAdio WiTH TEMPERATURE

loCATioN oF CoNTRolS

(see fig. 1)
1. MEMORY.SET/MEMORY+/ 12. BattErY coMpartMEnt
displaY light auto on/oFF/ (rEar oF unit)
nap 13. rEsEt
2. alarM 1 on/oFF sEt 14. rating laBEl (rEar oF unit)
3. alarM 2 on/oFF sEt 15. spEakEr
4. snooZE/slEEp/diMMEr 16. tEMpEraturE sEnsor (in
5. clk.adJ. (tiME sEt)/tEMp door)
6. <</TUNE-/YEAR/MONTH/DAY 17. FM antEnna
7. >>/TUNE+/DST/C-F 18. AC POWER CORD
8. VoluME up/displaY auto 19. pM indicator
changE on/oFF 20. standBY indicator
9. on/oFF 21. alarM 1 indicator
10. VOLUME DOWN 22. Mhz indicator
11. displaY 23. alarM 2 indicator

PoWER CoNNECTioN

Plug the AC power cord to a household outlet AC source. This unit is equipped
with a battery back up system, it requires a 1x3V CR2032 Flat Lithium battery
(Not included). Insert the battery in the battery compartment, making certain
that the positive and negative (+ and -) battery terminals are attached to the
corresponding terminals on the plate in the battery compartment. If an AC
power failure occurs, the clock automatically switches to the battery power
supply, the clock and timer memory continue running. When the AC power
resumes, the clock switches back to AC again.

gETTiNg STARTEd

Press the RESET button (13) locates on the back of unit after AC plug in.
• The unit will display full segment for 2 seconds, then it will enter the normal
mode.
1. TiME ANd CAlENdAR MANUAl SETTiNg
A. Setting Time and Calendar – Press Time set button (5) in normal mode and
keep depress over 2 seconds to enter time set mode, after enter the setting
mode, press Time set button (5) to change the mode cycle as follows:
Normal —> Year —> Month —> Day —> 12/24H —> Real time Hour —>
real time Min —> normal
Action (during data adjustment):
• Press <</Tune- button (6) to adjust data backward.
• Press >>/Tune+ button (7) to adjust data forward.
• Keep depress << or >> button for 2 seconds to enable auto forward.
B. Setting Alarm 1 and Alarm 2 – Press alarm set button (2/3) during normal
mode and keep depress over 2 seconds to enter alarm set mode, after enter
the setting mode, press alarm set button (2/3) to change the mode cycle as
follows:
Normal —> AL 1 Hour —> AL 1 Min —> AL 1 weekday Alarm —> AL 1 wake
beep —> AL 1 wake radio —> AL 1 wake radio volume —> Normal
2
Normal —> AL 2 Hour —> AL 2 Min —> AL 2 weekday Alarm —> AL 2 wake
beep —> AL 2 wake radio —> AL 2 wake radio volume —> Normal
Select alarm weekday mode as follows
1-5: Monday to Friday
1-7: Whole week
6-7: saturday & sunday
1-1: One day of week
Action (during data adjustment):
• Press <</Tune- button (6) to adjust data backward.
• Press >>/Tune+ button (7) to adjust data forward.
• Keep depress << or >> button for 2 seconds to enable auto forward.
2. SETTiNg AlARM oUTPUT oN/oFF
Press MEMORY.SET/MEMORY+/DISPLAY LIGHT AUTO ON/OFF/NAP
button (1) to the Auto off mode, alarm wake up the display is auto turn on.
Press alarm 1 on/off set button (2) to toggle on and off alarm output function.
Press alarm 2 on/off set button (3) to toggle on and off alarm output function.
3. AlARM dURATioN ANd SNooZE FUNCTioN
Alarm Duration – Beep alarm or radio alarm will continue output for 30 minutes
if no key press, then it will stop automatically and wait for same alarm time on
next day.
action for snooze:
• During alarming, press Snooze button (4) will enable snooze function, Beep
alarm or Radio alarm will stop.
• Snooze interval is 9 minute (not include second offset)
• Snooze will continue unless press ON/OFF button (12) to alarm off of
Buzzer alarm or radio alarm stop automatically after 30 minutes.
Press MEMORY.SET/MEMORY+/DISPLAY LIGHT AUTO ON/OFF/NAP
button (1) to the Auto off mode, during alarming display auto turn on, press
snooze/sleep button (4) will enable snooze function, buzzer alarm or radio/
display will stop & off.
4. CHANgE diSPlAY CoNTENT (see fig. 2)
Press <</Tune-/YEAR/MONTH/DAY button (6) during normal can switch to
display Year/Month/Day, after 5 seconds timeout and return back to display
time.
liSTENiNg To RAdio
Press the ON/OFF button (9) to turn the unit on.
Use the Tune+ or Tune- button to select the desired FM station. If you press
and hold the Tune+ or Tune- button for one second, the release, the unit will
automatically scan to the next broadcasting station.
Press the ON/OFF button (9) to turn the radio OFF.
To SET/RECAll THE RAdio PRESETS
Press the ON/OFF button (9) to turn the unit ON.
Use the Tune+ or Tune- button to select the desired FM station.
Press the memory/memory+ button; "P01" will blink in the display.
Press the memory/memory+ button again to set the preset.
Repeat steps 2 through 4 to set more presets.
The unit can preset 10 stations totally for FM.
3