Installation - V2 ELETTRONICA B-PACK Bedienungsanleitung

IMPORTANT REMARKS
For any installation problem please contact our Customer Service
at the number +39-0172.812411 operating Monday to Friday
from 8:30 to 12:30 and from 14:00 to 18:00.
V2 has the right to modify the product without previous
notice; it also declines any responsibility to damage or
injury to people or things caused by improper use or wrong

installation.

m
Please read this instruction manual very carefully
before installing and programming your control unit.
• This instruction manual is only for qualified technicians, who
specialize in installations and automations.
• The contents of this instruction manual do not concern the
end user.
• Every programming and/or every maintenance service should
be done only by qualified technicians.
The installation, testing and commissioning of door and
gate automation devices must be performed by qualified
and skilled personnel, who must assume responsibility
for setting up the tests envisaged depending on the risks
present; and verify compliance in accordance with legal and
regulatory requirements.
• V2 are not deemed responsible for injuries and damage
resulting from improper use of the product; other than that
envisaged in this manual.
• Packing materials must be disposed of in full compliance with
local regulations.
• Ensure that the back-up battery cannot become immersed in
water or other liquids.
• Should any liquids penetrate inside the device, disconnect it
immediately from the automation device and contact the V2
assistance service; use of the device under such conditions can
lead to hazardous situations.
• Do not store the back-up battery close to strong sources of
heat or expose it to naked flames; such actions can damage
it and be the cause of malfunctions, fire or other hazardous
situations
• In order to avoid the risk of leakage of hazardous substances
from the back-up battery in the case where the device is not
used for long periods of time, it is preferable to disconnect it
from the automated device and store it in a dry place.
EU DECLARATION OF CONFORMITY
V2 S.p.A. hereby declare that B-PACK equipment conforms to the
essential requirements established in directives:
• 2014/30/EU electromagnetic compatibility directive
• RoHS2 2011/65/EC
Racconigi, 01/06/2015
Legal representative, V2 S.p.A.
Giuseppe Pezzetto
DESCRIPTION AND INTENDED USE
The 161212 battery pack can only be installed in automated
systems for gates with V2 control units; it allows the accumulation
of energy during the period in which the automated device is
powered from the mains supply and to return it in the case of a
mains power failure.
The number of opening cycles possible during a power failure
depends on the power consumption of the automated device and
varies between a few tens to a hundred or so opening operations.
INSTALLATION
m
PLEASE NOTE: battery pack installation operations
must be conducted with the system disconnected from the
mains supply.
If the battery pack is installed inside a motor, follow the
instructions with the motor regarding the correct positioning and
connection of the device.
If the battery pack is installed outside a motor, in an environment
exposed to bad weather, it is essential the device be installed
inside a water-tight container.
ELECTRICAL CONNECTIONS
1. The device is supplied with the internal battery cables
disconnected; perform the connection operations by following
the diagram in figure 1.
2. Connect the battery pack to the control unit by inserting the
polarised connector A in the dedicated faston socket on the
control unit (figure 2).
3. If the cable is too short, use the extension provided:
a. insert the polarised connector C into the dedicated faston
socket on the control unit
b. bring the extension cable to the battery pack
c. fit connector B by crimping the two fastons on the
extension cable
PLEASE NOTE: Insert the fastons into the connector
while observing the polarity of the cable coming from
the battery pack
d. insert connector A into connector B
INDICATIONS
The status of the battery pack is displayed by means of 3 LEDs:
- Yellow LED: batteries charging
- Green LED: batteries fully charged
- Red LED: at least one battery has been connected wrongly
In the case of a blackout, the battery charger automatically
switches from recharge mode to back-up power supply mode (all
LEDs are off); on restoration of mains power, the battery charger
switches once more and the yellow LED comes on to indicate that
battery charging is ongoing.
m
PLEASE NOTE: during battery charging, the cover of
the battery changer can become hot; this is normal, and
should not cause any concern.
- 6 -