Appropriate Use; Specifications; Work Area; Inspection - Lincoln 1162 Bedienungsanleitung

AUTOMATIC AIR GREASE GUN
MODEL 1162

APPROPRIATE USE

· The Air Gun was exclusively designed to pump and
dispense lubricant using pneumatic power.
· The maximum specification rating should not be
exceeded.
· Any other use not in accordance with instruction will
result in loss of claim for warranty or liability.

SPECIFICATIONS

Pump ratio (max)
Output per stroke
Pneumatic Inlet pressure (min)
Grease output pressure (max)
Grease reservoir capacity
Operating temperature range
Weight (empty)
Weight (full)
Lubricant up to NLGI
Pneumatic port inlet
Grease Port Outlet

WORK AREA

Keep bystanders, children, and visitors away while
operating. Distractions can cause you to make mistakes.

INSPECTION

Visually inspect for damaged, loose or missing parts. If
equipment is worn or damaged, remove from service.
Contact an authorized service center for damage
assessment or repair.

OPERATION

Prime the Air Grease Gun after each refill or grease
cartridge change. Prime the gun before using it to lubricate
grease points.
For optimum performance and product life, add a few drops of
lubricating oil (SAE 30 or greater) through the air fitting at the
bottom of the handle if gun begins to cycle slowly or erratically.
© Indicates change
Page Number - 4
40:1
.038 in³ (0.62 cm³)
40 Psig (2.7 Bar)
(max) 150 Psig (10.3Bar)
6,000 Psig (414 Bar)
14.5 oz (450 cm³)
0 to 120 °F(-18 to +50°C)
4.5 Lbs. (2.0 Kg)
5.5 Lbs. (2.5 Kg)
#2 Grease
1/4-18 NPSF
7/16-28 UNEF
To prime, operate the gun slowly, by gently throttling the trigger
©
(8), until grease flows from the open end of the hose. The
vent/filler valve (18) should be used to expel air pockets. This
is done by loosening the vent/filler valve a couple of turns,
holding the gun with the discharge hose pointing up, and al-
lowing the air to escape. Close the vent/filler valve after air
is removed. If a prime can not be achieved after the gun has
operated for 10-15 seconds, see the section "TO EXPEL AIR
POCKETS".
The gun will stall if a bearing or fitting is blocked, causing the
©
grease pressure to rise to maximum. A blocked bearing or fit-
ting should be corrected before continuing lubrication.
Air pockets in the cartridge lubricant will cause the gun to
lose prime.

REMOVING EMPTY GREASE CARTRIDGE

1) Pull back on the follower handle until the follower
rod is fully extended and latch the follower rod
groove into the slot on the tube cap.
2) Unscrew the grease tube assembly from the gun.
3) Carefully release the follower handle to the eject
the empty cartridge from container tube.
INSTALLATION GREASE CARTRIDGE
1) Visually check the follower seal lip direction before
loading a new cartridge. The follower seal lip must be
directed toward handle or rear side for cartridge
loading. To change the direction of the follower seal,
unscrew tube cap from grease tube assembly and pull on
the handle to remove follower seal from tube. Flip follower
seal over and reassemble.
2) Pull back on the follower handle and latch the
follower rod groove into the slot on the tube cap.
3) Remove the plastic cap from the grease cartridge
and insert cartridge into container tube.
4) Remove the pull tab from the grease cartridge
and screw grease tube assembly into pump assembly.
5) Release follower rod from slot. Purge air from pump.
See air purging instruction.
Form 420110