VOLTCRAFT PM-45 Bedienungsanleitung Seite 3

Operating instructions
PM-45 USB power meter adapter
Item no. 1716077
Intended use
The product acts as an adapter for a digital or analogue multimeter to measure the voltage or
current on the connected device. The adapter can measure devices with a voltage of 5 V/DC
(max. 10 V/DC) and a current of up to 2.4 A using a multimeter.
This product is intended for indoor use only. Do not use it outdoors. Contact with moisture
(e.g. in a bathroom) must be avoided under all circumstances.
For safety and approval purposes, do not rebuild and/or modify this product. Using the product
for purposes other than those described above may damage the product. In addition, improper
use can cause hazards such as a short circuit, fire or electric shock. Read the operating
instructions carefully and store them in a safe place. If you pass the product on to a third party,
please hand over these operating instructions as well.
This product complies with statutory, national and European regulations. All company and
product names contained herein are trademarks of their respective owners. All rights reserved.
Package contents
• USB power meter adapter
• 4 pairs of test leads (1x black, 3x red)
• Operating instructions
Up-to-date operating instructions
To download the latest operating instructions, visit www.conrad.com/downloads or scan the QR
code on this page. Follow the instructions on the website.
Explanation of symbols
The symbol with the lightning in a triangle indicates that there is a risk to your health,
e.g. due to an electric shock.
The symbol with an exclamation mark in a triangle is used to highlight important
information in these operating instructions. Always read this information carefully.
The arrow symbol indicates special information and tips on how to use the product.
Safety instructions
Read the operating instructions carefully and observe in particular the safety
instructions. If you do not follow the safety instructions and information on
proper handling in these operating instructions, we assume no liability for any
resulting personal injury or damage to property. Such cases will invalidate the
warranty/guarantee.
a) General information
• The product is not a toy. Keep out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. It may become a
dangerous plaything for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high
humidity, moisture, flammable gases, vapours and solvents.
• Never expose the product to mechanical stress.
• If it is no longer possible to operate the product safely, stop using it and prevent
unauthorised use. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height
may damage the product.
• Always observe the safety instructions and operating instructions of any other
devices which are connected to the product.
• When setting up the product, make sure that the cables are not pinched, kinked
or damaged by sharp edges.
• Always lay the cables so that nobody can trip over or become entangled in them.
This poses a risk of injury.
• Never pour liquids over electrical devices or place objects filled with liquid next to
the device. If liquid or an object gets into the device, power down the respective
mains socket (e.g. switch off the circuit breaker), and then pull the mains plug
from the mains socket. Discontinue use and take the product to a specialist repair
centre.
• Never use the product immediately after it has been brought from a cold room into
a warm one. The condensation generated could destroy the product. Allow the
product to reach room temperature before connecting it and putting it to use. This
may take several hours.
• Never leave the product unattended during use.
• Do not short-circuit the USB ports.
• Trained personnel must supervise the use of electrical appliances in schools,
training facilities and DIY workshops.
• On commercial premises, the relevant accident prevention regulations for
electrical equipment must be complied with.
• Check the product for damage before each use! If you notice any damage, do not
use the product any longer! Disconnect it from connected devices (e.g. multimeter,
power supply). Take the product to a specialist repair centre.
• Check the meter and test leads for signs of damage before each measurement.
• Never take measurements if the protective insulation is damaged (torn, missing,
etc.).
• To prevent an electric shock, do not touch the measuring points when taking
measurements, either directly or indirectly.
• Avoid using the device in the immediate vicinity of:
- strong magnetic or electromagnetic fields
- transmitting antennas or HF generators.
These may distort the measurements.
• Consult a technician if you are not sure how to use or connect the product, or if
you have concerns about safety.
• Maintenance, modifications and repairs must only be carried out by a technician
or a specialist repair centre.
• If you have any questions that are not answered in these operating instructions,
please contact our technical customer service or other professionals.
Product overview
IN
OUT
1 USB-A plug
2 Connector V – (voltage)
3 Connector V + (voltage)
4 USB-A port
OUT
IN
V A
5 Connector A + (current)
6 Connector A + (current)
7 Test leads (4 pairs: 1x black, 3x red)
1
2
3
4
5
6
7