Product Disposal - Nice Nemo series Installierungs-Und Gebrauchsanleitungen Und Hinweise

(on the control unit) of all commands for 15 minutes.
• Second example: after descent of the awning caused
by values exceeding the sun threshold, if the user sends
an Up command via a transmitter, the control unit acti-
vates the "manual priority" status. From this moment
onwards, the control unit ignores all subsequent com-
mands sent by Nemo, caused by values "exceeding the
sun threshold" and normal operation is restored when
Nemo sends the command "end of values exceeding sun
threshold".
To cancel blocks generated during the test phase, sim-
ply switch off the control unit (or motor) controlled by
Nemo for a few seconds.
On completion of the checks in TEST mode, the Sun and
Wind sensor knobs can be set to the required values,
using the graduated scale next to the knobs as a refer-
ence.
• "Sun" knob
As a guideline, this knob should be set to between 15
and 30Klux. If the automation needs to be activated in
the case of very intense sunlight, set the knob to a higher
value.
Otherwise, the "real time" mode can also be used to set
the Sun knob. To use this mode, turn the Sun knob
through small sections and each time wait for a few sec-
onds, to that Nemo can compare the set threshold with
the light value measured at that time, and then transmit
the envisaged command to the automation. In this case
the led emits one of the following signals: green flashing =
threshold exceeded; alternating red and green flashes =
threshold not exceeded.
• "Wind" knob
As a guideline, this knob should be set to between 15
and 30Km/h; it can only be set to higher values in the
case of small and very sturdy awnings.
7 – DIAGNOSTICS
It is possible to check at any time whether the intensity of
the atmospheric phenomena at the time is below or
above the set threshold by activating "DIAGNOSTIC"
mode.
To activate diagnostics, briefly press "P1" (fig. 6) and wait
for approx. 1 second when the red led stops flashing,
4
then check the led signal and compare this with the
description in Tabla A.
Caution! - "Diagnostic" mode only generates the led
signal and not an awning command.
8 – DISABLING THE SUN SENSOR
To disable the sun sensor, for example in the winter, turn
the "Sun" knob (fig. 6) clockwise to the maximum setting.
To enable the sensor, turn the knob to the required set-
ting and briefly press "P1" (fig. 6).
Caution! - The wind sensor cannot be disabled.
9 – TROUBLESHOOTING...
If the wind or sun exceeds the set threshold but the
automation seems not to perform the ma noeuvre
correctly: • ensure that Nemo is correctly memorised in
the receiver of the automation to be controlled, as fol-
lows: Send a command to the automation by means of
another transmitter, then press P1 on Nemo to ensure
that the manoeuvre is stopped. • Check correct opera-
tion of the sensors by running the diagnostics function
described in chapter 7. • Then perform the TEST de -
scribed in chapter 6.
Table A
• Led off
No threshold has been exceeded and there is no pre-
alarm.
• Red Led lit (for 3 seconds)
The set wind threshold has been exceeded
• Green Led lit (for 3 seconds)
The set sun threshold has been exceeded
• Red flashing Led (for 3 seconds)
Pre-alarm: fault on "wind" sensor this has not detect-
ed wind action in the last 24 hours
• Green flashing Led (for 3 seconds)
Pre-alarm: fault on "sun" sensor this has not detected
any variation in sunlight intensity in the last 24 hours

PRODUCT DISPOSAL

This product is an integral part of the automation,
and therefore must be disposed of together with the
latter.
As in installation, also at the end of product lifetime, the
disassembly and scrapping operations must be per-
formed by qualified personnel.
This product comprises various types of materials: some
may be recycled and others must be disposed of. Seek
information on the recycling and disposal systems envis-
aged by the local regulations in your area for this product
category.
Caution! - some parts of the product may contain pollu-
tant or hazardous substances which, if disposed of into
the environment, may cause serious damage to the envi-
ronment or physical health
As indicated by the symbol alongside, dis-
posal of this product in domestic wa ste is
strictly prohibited. Separate the wa ste into
categories for disposal, according to the
methods envisaged by current legislation in
your area, or return the product to the retailer when pur-
chasing a new version.
Caution! – Local legislation may envisage serious fines in
the event of abusive disposal of this product.
Battery disposal
Caution! – The product contains a battery that must be
removed prior to disposal. The discharged battery con-
tains pollutant substances and therefore must not be dis-
posed of as common household waste. Dispose of
according to separate waste collection procedures as
envisaged by local current standards.