Technical Data - Felisatti AGF110/1010E Bedienungsanleitung

TECHNICAL DATA

Burnishing tool for steel
Input power
No-load speed
Max diameter of the smoothing disk
Approx. weight (without acces.)
The instructions contained in this manual must be strictly
followed, it should be carefully read and kept close at
hand to use when carrying out maintenance on the
indicated parts.
If the machine is used carefully and normal maintenance
is carried out, it will work well for a long time.
The functions and use of the tool you have bought shall
be only those described in this manual. Any other use
of the tool is strictly forbidden.
ILLUSTRATIONS
DESCRIPTION (See figures)
A Start-up switch (Fig.1)
B Auxiliary handle M10 (Fig.1-2)
C Spindle blocking button (Fig.2-3)
D Smoothing disk (Fig.1-2)
E Auxiliary handle M8 (Fig.1-2)
F Protection smoothing disk (Fig.1-2-3)
G Washer seating (Fig.2)
H Fixing screw for the smoothing disk (Fig.2)
I Fixing nut for the auxiliary M8 handle (Fig.2)
J Adjustment key (Fig.2)
EQUIPMENT
- 2 auxiliary handles
- 1 Allen wrench to change the smoothing disk
- Operating instructions
- Instrucciones de seguridad
- Warranty
SAFETY INSTRUCTIONS
 See "Safety Instructions" manual, supplied with this
 WARNING! Material containing asbestos must not be
instruction manual.
polished. Working with materials containing amian-
thus/asbestos and/or silica stones produces a dust,
which is harmful to health. Protect yourself from inhal-
ing this dust, in compliance with current regulations on
 For your personal safety, always connect the machine
accident prevention.
to a mains supply protected by a differential and ther-
mal cutout switch, in accordance with regulations on
 Do not pierce the motor housing as this could damage
low-voltage wiring sitemaps.
 Check the work area with a metal detector for hidden
the double insulation (use adhesive labels).
 Always unplug the machine before carrying out work
wires, gas and/or water pipes.
 Always stop the machine by switching it off, not by
on it.
 WARNING! Before each use, inspect the plug and
unplugging it.
lead. Should they need replacing, have this done by an
official service centre.
W
rpm
mm
Kg
 Always keep the mains lead clear of the working range
 Only plug the machine in when it is switched off.
of the machine.
 Always use the machine with the auxiliary handle
 Hold the machine firmly in both hands and in a stable
attached.
 Check that the speed set on the smoothing disk is
position.
the same or higher than the nominal speed of the
 Make sure that the dimensions of the smoothing disk
burnishing tool.
 The smoothing disks must be used and maintained
are compatible with those of the burnishing tool.
 Protect the polisher from knocks, collisions and
carefully according to manufacturer's instructions.
 Before using, carefully check that the smoothing disk is
grease.
not damaged or cracked. Immediately replace dam-
 Make sure that the smoothing disks are assembled
aged or cracked smoothing disks.
 Check that the disc has been properly fitted and se-
according to manufacturer's instructions.
cured before using the machine. Start the machine
with no load and run for 30 seconds in a safe position;
if you notice serious vibration or any other defect stop
the machine immediately. This could indicate an incor-
 Use only clamps or plates specified for this tool. Do not
rect installation or a poorly balanced smoothing disk.
use separate reducing tubes or adapters to ajust the
 Machine created to work with 19 mm (interior diame-
smoothing disks to large holes.
 Check the correct fixing of the piece to be worked on
ter) smoothing disks.
 Beware of shavings that fly off. Hold the tool that so
before starting any polishing/burnishing operation.
that sparks fly away from you or other people and in-
 For efficient work, always choose the right size and
flammable materials.
type of disk, open or closed disk structure or other
polishing disks or wire brushes found in the market
 Do not touch rotating polishing tools.
based on the material and surface finish.
 WARNING! The smoothing disk will remain in opera-
 When working with the machine, always wear safety
tion for a short time after the device is disconnected.
goggles and ear protection. Other personal protection
equipment such as dust masks, gloves, helmet and
apron should be worn when necessary, along with
non-slip safety footwear. When considering the need
to use a protective mask against the dust, this should
also be for the possible harmful effects of the polished
material and paint or other surface coating. If in doubt,
 Make sure the vents are free when working with
use safety equipment.
dust. If they require cleaning, first unplug the ma-
AGF110/1010E
1010
1200-3900
110x100
2