Rear Panel - Tascam 102i series Bedienungsanleitung

7 PHONES knob
Use to adjust the output levels of the PHONES
V CAUTION
Before connecting headphones, minimize the volume with the
PHONES knob. Failure to do so could result in a sudden loud
noise that could harm hearing, for example.
8 1-2 input jacks
These analog inputs are XLR/TRS combo jacks.
They can support high impedance input, including direct gui-
tar input.
Use the input switches on the front of the unit to select bal-
anced line (MIC/LINE) or unbalanced (INST) input for the TRS
jacks.
When directly connecting a guitar, bass or other instrument,
INST
set the input switch to
9 Input switches
Set according to the input source of each input jack.
INST : Select when connecting a guitar, bass or other high-im-
pedance instrument. This makes it an unbalanced input
for high impedance.
MIC/LINE
: Select when connecting a balanced-output mic or
line-level-output device.
+48V
: This provides +48V phantom power to the
on SERIES 208i) XLR input connectors.
0 +48V indicators
These indicators light when their input switches are set to
+48V
.
q 3-4 input jacks (SERIES 208i only)
These analog inputs are XLR/TRS combo jacks.
They also support high impedance input, including direct gui-
tar input.
Use the input switches on the front of the unit to select bal-
anced line (MIC/LINE) or unbalanced (INST) input for the TRS
jacks.
When directly connecting a guitar, bass or other instrument,
INST
set the input switch to
w MONITOR knob
Use to adjust the output level of the
1-2
jacks on the back of the unit.
e PHONES / jacks
Use this standard stereo jack to connect stereo headphones.
These output the same signals as the
1-2
jacks on the back of the unit.
Use an adapter to connect headphones with a mini plug.
NOTE
The same signals are output from both the
PHONES
jacks.
and jacks.
.
1-2
(and
.
LINE OUT (BALANCED)
LINE OUT (BALANCED)
PHONES

Rear panel

SERIES 102i
SERIES 208i
r Kensington Security Slot
3-4
t WORD IN/OUT connectors (SERIES 208i only)
These BNC connectors are for the input and output of word
clock signals.
Word clock signals of 44.1, 48, 88.2, 96, 176.4 and 192 kHz can
be input and output.
ATTENTION
If a digital system has multiple word clock masters, serious
problems, including damage to equipment, could occur.
y 75Ω ON/OFF switch (SERIES 208i only)
When this switch is set to
nates to 75 Ω.
u STANDBY switch
Press to turn the unit on and to put it into standby.
i Cord holder
Hook the cord of the included PS-P1220E AC adapter here to
prevent accidental disconnection.
o LINE OUT (BALANCED) 3-8 jacks (SERIES 208i only)
These standard TRS jacks are analog line outputs.
The nominal output level is +4 dBu.
(Tip: HOT, Ring: COLD, Sleeve: GND)
p LINE OUT (BALANCED) 1-2 jacks
These standard TRS jacks are analog line outputs.
and
The nominal output level is +4 dBu.
(Tip: HOT, Ring: COLD, Sleeve: GND)
a MIDI OUT connector
This 5-pin DIN is a standard MIDI output connector.
This outputs MIDI signals.
s MIDI IN connector
This 5-pin DIN is a standard MIDI input connector.
Use this to input MIDI signals.
d OPTICAL IN (S/MUX) connector(s)
These input multichannel digital audio in optical format.
44.1, 48, 88.2, 96, 176.4 and 192 kHz sampling frequencies are
supported.
88.2/96 kHz is supported by S/MUX2, and 176.4/192 kHz is
supported by S/MUX4.
TASCAM SERIES 102i / SERIES 208i
ON WORD IN
, the connector termi-
7