Werbung
GB
CEMO UNI-Tank / MULTI-Tank 1500 l
Tank documents and technical information,
Approval No.: Z-40.21-432
1. Approval „OPERATOR EXCERPT"
2. Transport, installation and
operating instructions
3. Inspection declaration
Important documents for the operator!
Please keep in a safe place!
(Documents are to be presented during inspections
of the tank system.)
8
1. Approval „OPERATOR EXCERPT"
This is a translation of the German original document and has not
been reviewed by the German Institute for Structural Engineering.
page
8-11
National Technical
page
12
Approval
National Technical
page
12
Approval
Approval number:
Z-40.21-432
Approval number:
Z-40.21-432
Applicant:
CEMO GmbH
In den Backenländern 5
Applicant:
71384 Weinstadt, Germany
CEMO GmbH
In den Backenländern 5
71384 Weinstadt, Germany
Object of approval:
Blown polyethylene containers (PE-HD)
with integrated collecting device made of galvanised sheet steel
Object of approval:
Type UNI-Tank 1500 I
Blown polyethylene containers (PE-HD)
Container system
with integrated collecting device made of galvanised sheet steel
Type UNI-Tank 1500 I
Container system
The above object of approval is hereby granted National Technical Approval.
This National Technical Approval includes ten pages and four annexes with 7 pages.
The above object of approval is hereby granted National Technical Approval.
The object first received national technical approval on 17 October 2008.
This National Technical Approval includes ten pages and four annexes with 7 pages.
The object first received national technical approval on 17 October 2008.
DIBt | Kolonnenstraße 30 L | D-10829 Berlin | Tel.: +493078730-0 | Fax: +493078730-320 | Email: dibt@dibt.de | www.dibt.de
DIBt | Kolonnenstraße 30 L | D-10829 Berlin | Tel.: +493078730-0 | Fax: +493078730-320 | Email: dibt@dibt.de | www.dibt.de
National Technical Approval
No. Z-40.21-432
I
1
2
3
4
5
6
7
Z58413.15
Approval office for constructed products and design
types
Approval office for constructed products and design
Technical Inspection Office
types
An institution supported by the German federal and state
Technical Inspection Office
governments under public law
An institution supported by the German federal and state
Member of the European Organisation for Technical
governments under public law
Approvals (EOTA), the Union Européenne pour l'Agrément
technique dans la construction (UEAtc) and the World
Member of the European Organisation for Technical
Federation of Technical Assessment Organisations (WFTAO)
Approvals (EOTA), the Union Européenne pour l'Agrément
technique dans la construction (UEAtc) and the World
Federation of Technical Assessment Organisations (WFTAO)
Date:
19 August 2015
Date:
19 August 2015
Period of validity
from: 1 October 2015
Period of validity
to: 1 October 2020
from: 1 October 2015
to: 1 October 2020
GENERAL PROVISIONS
National technical approval certifies that the object of approval can be used and/or
employed within the meaning of the German state building codes.
Where national technical approval requires special knowledge and experience from persons
responsible for manufacturing construction products and design types pursuant to § 17,
Para. 5 of the Model Building Code in German state regulations, it should be noted that this
specialist knowledge and experience can be attested by equivalent documentation issued
by other member states of the European Union. This also applies to attestations provided
within the context of the Treaty establishing the European Economic Community (EEC) or
other bilateral agreements, if applicable.
National technical approval does not replace the permits, approvals and certifications
required by law in connection with the realisation of building proposals.
National technical approval is granted without prejudice to the rights of third parties,
particularly in respect of private property rights.
Without prejudice to more extensive regulations contained in the "Special Provisions", the
manufacturers and distributors of the object of approval shall make copies of the National
Technical Approval available to indirect and direct users of the object of approval and shall
inform them that the National Technical Approval must be present at the site of use of the
object. Copies of the national technical approval shall be made available to the relevant
authorities on request.
The national technical approval may only be reproduced in its entirety. Publication of
excerpts requires permission from the German Institute for Structural Engineering (DIBt).
Text and drawings used in advertising must not contradict the national technical approval. In
the event of differences between the German version of the national technical approval and
its English translation, the German version shall take precedence. Translations of the
national technical approval must bear the notice: "This is a translation of the German
original and has not been reviewed by the Deutsches Institut für Bautechnik."
The national technical approval can be revoked at any time. The provisions of the national
technical approval may subsequently be amended or supplemented, particularly if required
by new technical findings.
Code:
II 27-1.40.21-43/15
Code:
II 27-1.40.21-43/15
Page 2 of 10 | 19 August 2015
1.40.21 - 43/15
Werbung
