Werbung
National Technial Approval
N0. Z-40.21-432 of 19 August 2015
Blown polyethylene (PE-HD) container with integrated
collecting device made of galvanised sheet steel. Type:
UNI-Tank 1500 l container system
Packaging, transport and storage
1
Moulding compounds for inner container
(4) For the manufacture of the inner containers, only the moulding compounds listed in
Table 1 below may be used with the material parameters specified there.
Table 1: Moulding compounds, material parameters
Type designation
Manufacturer
Designation pursuant to DIN EN ISO
1
1872-1
Alcudia 49070 UV
Repsol Quimica
BAHN, 50 G 090
(5) The moulding compound must be fabricated with at least 70% virgin and no more than
30% recycled compound. The use of regranulates is not permitted.
2
External container
Material: Galvanised sheet plate pursuant to DIN EN 10346
Walls:
DX 51 D+ Z 275 or ZA 255
Front parts:
DX 52 D+ Z 275 or ZA 255
Cover:
DX 53 D+ Z 275 or ZA 255
Sealing material for flanged seam (see stored documents):
-
Oil-resistant sealant "Duraflex KN 9 PU" from Arawerke,
-
Alternative: NBR seal 6x1 one-sided, self-adhesive
3
Steel foot
Material:
S 235 JR, hot-dip galvanised
Material:
DX 51 D Z275 or DX 51 D ZA 255
The plate thickness/dimensions for the respective steel foot are listed in the stored
documents.
4
Container accessories, spacers
The materials and details are listed in the graphical annexes as well as in the stored
documents.
1
DIN EN ISO 1872-1:1999-10 Polyethylen (PE) moulding compounds, Part 1: Designation system and basis for
specifications
2
DIN EN 10346:2009-07
Continuously hot-dip coated steel strip and sheet; Technical delivery conditions;
German version EN 10346:2009
Z58413.15
National Technial Approval
N0. Z-40.21-432 of 19 August 2015
Blown polyethylene (PE-HD) container with integrated
collecting device made of galvanised sheet steel.
Type: UNI-Tank 1500 l container system
Packaging, transport and storage
1
Packaging
The containers do not need to be packaged for transport or (temporary) storage if the
requirements of section 2 are met. All nozzle openings shall be closed by screwing on the
caps.
2
Transport, storage
2.1
General
Transport shall be carried out only by companies with specialist experience, suitable
machinery, equipment and means of transport, and adequately trained staff. To prevent
danger to employees and third parties, the relevant accident prevention regulations shall
be observed.
2.2
Preparation for transport
(1) The containers shall be prepared for transport such as to ensure that no damage can
occur during loading, transport and unloading.
(2) The loading surface of the transport vehicle shall be designed such as to exclude the
possibility of containers being damaged by impact or pressure due to point loading.
2.3
Loading and unloading
(1) Impact loads shall be avoided when lifting, moving and setting down the containers.
(2) If a forklift is used, the containers shall be secured while they are being moved with the
forklift.
(3) Nozzles and other protruding parts of containers shall not be used for lashing or lifting.
The containers shall not be dragged over the ground or floor.
2.4
Transport
(1) The containers shall be secured so that they cannot shift position during transport.
(2) The manner in which containers are fastened must not cause any damage.
2.5
Storage
(1) When temporarily stored outside, the containers should be protected from damage and
storms. Containers may not be exposed to the elements for more than 6 months.
(2) It is imperative to ensure that no rainwater can penetrate between the inner and
collecting containers.
2.6
Damage
For damage caused during transport or storage, the course of action shall be based on the
findings of an expert on water legislation or the certification agency.
Z58413.15
Annex 2
Melt index
Density at 23°C
MFI 190/21.6
[g/cm³]
[g/10 min]
8.5 ± 1.5
0.949 ± 0.002
2
Plate thickness: 1 mm
Plate thickness: 1 mm
Plate thickness: 0.75 mm
or
1.40.21 - 43/15
Annex 3
1.40.21 - 43/15
GB
11
Werbung
