Herunterladen Diese Seite drucken

Velleman VISP2 Kurzanleitung

Schwenk-/neige-system für kamera

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

VISP2 – INDOOR CAMERA PAN-TILT MOTOR 24V AC
1. Introduction
Thank you for buying the VISP2! Please read the manual thoroughly before bringing this device into service.
If the device was damaged in transit, don't install or use it and contact your dealer.
2. Installation & Maintenance
Install the unit on a wall bracket by means of the 2 included stainless steel M6x15 screws. Secure the VISP2 to the
wall bracket by fastening the screws from the bottom of the wall bracket into the unit.
The VISP2 requires no lubrication or maintenance for the life of the unit.
3. Wiring
Compose the interconnecting cable in accordance with the figure below for proper operation.
1. COMMON (red)
2. AC24V/AUTO (black)
3. TILT DOWN (blue)
4. TILT UP (yellow)
5. PAN RIGHT (green)
6. PAN LEFT (white)
Inverted Mounting: when the unit is mounted in the inverted position, the left-right directions are reversed for manual
operation. This must be corrected when wiring the cable between control unit and the VISP2. Simply reverse the
leads going to terminals 5 and 6.
4. Adjusting Limit Stops
1. Camera Mounting Plate
2. Limit switch
3. Right/left pan limit stop
4. Connection to control (VSCP1)
When the cable is installed and unit has been mounted, plug the control unit into
AC 24V source. Make sure the auto switch is in the OFF position. Adjust the pan
limit stops by taking them off and putting them where you want them to be.
5. Specifications
Angular travel
Limited Stop
Speed
Load Rating
Input Voltage
Power Consumption
Cable Requirement
Operating Temperature
Construction
Finish
Dimensions
Weight
The information in this manual is subject to change without prior notice.
VISP2
Pan: 355° / Tilt: ± 100°
Externally adjustable
Pan/tilt: 5° / second
7 kg
24Vac
7W
Six-conductor, unshielded
-5°C to + 60°C
plastic
beige
179 x 115 x 180mm
1.6kg
- 1 -
VELLEMAN

Werbung

loading

Inhaltszusammenfassung für Velleman VISP2

  • Seite 1 2. Installation & Maintenance Install the unit on a wall bracket by means of the 2 included stainless steel M6x15 screws. Secure the VISP2 to the wall bracket by fastening the screws from the bottom of the wall bracket into the unit.
  • Seite 2 De module moet op een wandhouder gemonteerd worden. Om de zwenk- en kantelmodule op de wandhouder te bevestigen, heeft u de 2 roestvrijstalen schroeven M6x15 nodig die samen met de VISP2 geleverd wordt. Steek de schroeven door de onderkant van de wandhouder in de module en draai ze stevig aan.
  • Seite 3: Spécifications

    2. Installation & maintenance Installez le VISP2 sur un support mural avec les 2 vis M6x15 en acier inoxydable inclus. Fixez le dispositif au support mural en insérant les vis dans le dispositif par le côté inférieur du support mural. Serrez bien les vis.
  • Seite 4: Especificaciones

    Si el aparato ha sufrido algún daño en el transporte no lo instale y póngase en contacto con su distribuidor. 2. Instalación & mantenimiento Instale el VISP2 con los 2 tornillos M6x15 de acero inoxidable (incl.) en un soporte mural. Fije el aparato al soporte mural introduciendo los tornillos en la parte inferior del soporte mural. Apriételos bien.
  • Seite 5 Montieren Sie die Einheit auf einem Wandbügel mithilfe der 2 mitgelieferten rostfreien M6x15 Schrauben. Befestigen Sie das VISP2 an der Wand, indem Sie die Schrauben von der Unterseite des Wandbügels in die Einheit einschrauben. Das VISP2 erfordert keine Schmierung oder Wartung während der Lebensdauer.