Operation; Cleaning And Maintenance; Troubleshooting - Somogyi Elektronic FKK 06 Bedienungsanleitung

03. The unit may only be used indoors in dry conditions!
04. Do not locate the appliance directly below a wall outlet!
05. Remove the protective foam padding from the product and put them back into the carton, in their original
location. Place the appliance on the carton laid onto the floor with the glass panel facing upwards.
06. Remove the glass panel from the heater by sliding the glass panel toward the switches. Place the
glass panel in a safe location, away from where the appliance is being assembled. Do not remove
protective film from the glass yet.
07. According to Figure 3, fasten the wall mount (9) horizontally to the wall at the desired location using
the included screws and dowels. The recommended 600mm installation height is not mandatory,
however, the minimum height of 300mm above the floor must be observed! The wall mount should
be flush with the wall. Please take into account the wall's bearing capacity!
08. Using the 2 included small screws attach the lift-off prevention plate (10) onto the bottom of the
heater so that the plate is flush with the wall surface.
09. Hang the heater onto the wall mount!
10. Mark the screw holes of the lift-off prevention plate on the wall.
11. Remove the heater from the wall then drill holes of appropriate size to accommodate the dowels
into the wall. Insert the dowels into the holes.
12. Hang the heater back onto the wall mount then fasten the lift-off prevention plate using the screws.
13. Make sure the device is stably placed on the wall!
14. Hang the glass panel onto the heater at the two fixing points on either side.
15. Verify that the unit's mains switch is in the OFF "0" position!
16. Insert 2 AAA size (1,5 V) alkaline batteries into the remote controller. Insert the battery considering
the polarity!
17. Plug the unit's standard grounded AC power cable into a grounded wall outlet. Now the unit is
ready for operation!
Caution: Risk of electric shock! Do not attempt to disassemble or modify the unit or its
accessories. In case any part is damaged, immediately power off the unit and seek the assistance of
a specialist.
In the event that the power cable should become damaged, it should only be replaced by the
manufacturer, its service facility or similarly qualified personnel.
Meaning of symbol on appliance: Do not cover!
Covering the unit can cause overheating, fire or electric shock!
FEATURES
electric wall-mounted decorative fireplace with built-in fan heater for heating the atmosphere of indoor premises • attractive flame effects • tempered glass front panel • energy saving LED light
source • adjustable brightness • switchable output stages (1000 W / 2000 W) • blow out point on the top • overheating protection • remote controller included
STRUCTURE (Figure 1.)
1. glass front panel • 2. heating element • 3. cold air inlets • 4. warm air outlet grill • 5. mains switch • 6. ON/OFF button • 7. heating stage selector buttons • 8. power cable • 9. wall-mount console •
10. lift-off prevention plate • 11. screws and dowels for mounting
Functions of remote controller buttons:
12. ON/OFF switch • 13. heating stage selector buttons • 14. brightness control button

OPERATION

The appliance can be operated using the push-buttons located on the top or using the remote controller.
The unit may emit a slight odor when turned on initially, which is not a malfunction. It is harmless and evaporates quickly.
Set the mains switch (5) to the I (On) position. The unit will emit a short beep.
The appliance can be switched on or off using the I/O push-button on top of the unit.
By being switched on, the flame effect will begin to operate only, without any heating function. Keeping the I/O button pressed will toggle among five brightness settings for the flame effect. The
built-in fan heater can be activated in two stages, 1000 W and 2000 W by using the push-buttons. Pressing the same buttons again will switch off the corresponding heating stage. The appliance
can be switched off anytime using the I/O push-button.
The ON/OFF button on the remote controller functions in the same way as the I/O button on the appliance. The 1000 W and 2000 W buttons on the remote can be used switch on or off the
corresponding heating stages. The currently selected stage can be checked on the appliance. The DIMMER button can be used to adjust the brightness of the flame effect in 5 increments.
The built-in energy saving and electronically controlled LED light source doesn't require replacement, it is not replaceable.
In the event of overheating, the overheating protection function will switch off the unit, for example, when the air inlets and outlets are covered. Power off the unit by unplugging it from the electric
outlet. Allow the appliance to cool (for at least 30 minutes). Check whether the air inlets and outlets are obstructed or not, and clean them if necessary. Switch on the unit again. If the overheating
protection activates again, power off the unit by unplugging it from the electric outlet and contact the service facility.
After use, please turn off the appliance using the mains switch (5).

CLEANING AND MAINTENANCE

In order to ensure optimum functioning, the unit may require cleaning at least once a month, depending on the manner of use and degree of contamination.
1. Switch off and power off the unit by unplugging it from the electric outlet before cleaning!
2. Let he appliance to cool (for at least 30 minutes).
3. Use a vacuum cleaner to clean the air inlets (1) and outlets (2)!
4. Use a slightly moistened cloth to clean the unit's outer surface. Do not use aggressive cleaners. Avoid getting water inside onto the electric components of the appliance!

TROUBLESHOOTING

Malfunction
The appliance does not heat.
Flame effect does not work.
The overheating protection activates frequently.
The unit does not respond to the remote controller's signal.
Solution
Check the power supply.
Check the information written at section of overheating.
Check the power supply.
Clean the appliance.
Check the remote controller's batteries.