Global garden products RM 135 Gebrauchsanweisung Seite 34

GB
6. Disconnect both thick hydraulic hoses at the
socket on the machine.
7. Set the catch (7:D) to the rear position so that it
can lock.
8. Grip the front edge of the deck and lift up until
the deck locks in the first locking position.
See fig. 10.
RM 135 - RM 155:
3. Set the minimum cutting height. Otherwise the
hydraul hoses might be damaged.
4. Stop the engine
5. Disconnect both thick hydraulic hoses at the
socket on the machine. See fig. 8.
6. Remove both pins (5:B) and remove any wash-
ers.
7. Set the catch (9:E) to the rear position so that it
can lock.
8. Grip the front edge of the deck and lift up until
the deck locks in the first locking position.
See fig. 10.
6.3 SERVICE POSITION
It is absolutely forbidden to start the
engine when the deck is in the service
position.
1. Set the deck to the cleaning position. See above.
2. Grip the front edge of the deck and lift up fur-
ther until the deck locks in the second locking
position. See fig. 11.
6.4 RESETTING
Two people are required to reset from the cleaning
and service position as follows:
1. Person 1 lifts the deck at the front edge so that
it releases from catch (7:D RM 125)(9:E RM
135 - RM 155).
2. Person 2 sets the catch to the front position.
3. Person 1 carefully lowers the deck to the
ground.
4. Other connections are made according to the
relevant section under "3".
6.5 CLEANING
The underside of the deck must be cleaned after
each use.
Set the deck in the cleaning position.
Clean the underside of the deck thoroughly. Use
water and a brush.
When the surfaces are completely dry and clean,
touch up the paintwork. Use durable paint intended
for metal outdoors.
34
ENGLISH
6.6 LUBRICATION
Lubricate all lubrication points according to the ta-
ble below.
The three cutting shafts must be lubricated every
100 operating hours as well as after each clean.
Other lubrication points must be lubricated every
250 hours of operation.
Use a grease gun, filled with universal grease for
the grease nipples. Pump until grease protrudes.
RM 125:
The lubrication points are shown in fig. 14.
Object
Bearing, belt ten-
sioner
Cutting shafts
Bearings, link
wheel
Bearing on right
and left sides
RM 135 - RM 155:
The lubrication points are shown in fig. 15.
Piece
Bearings, belt ten-
sioner
Bearings for the
rear ejector hatches
and hydraulic cyl-
inders
Cutting shafts
Bearings, link
wheel
Links and bear-
ings on the right
and left sides
6.7 REPLACING BLADES (12:F)
Wear protective gloves when changing
blade(s) to avoid cutting yourself.
Check that the blades are always sharp.
This produces the best cutting results.
Always check the blade(s) after a collision. If the
blade system has been damaged, defective parts
should be replaced.
Always use genuine spare parts. Non-
genuine spare parts can entail a risk of
injury, even if they fit the machine.
Install the new blade with the punched
text facing down.
The deck has two right-hand rotating blades and
one left-hand rotating blade. Direction of rotation
is defined seen from above. The left-hand rotating
Lubrication nipples Figure
/ action
1 lubrication nipple
3 lubrication nipples
4 lubrication nipples
2 lubrication nipples.
Lubrication nipples
/ action
2 lubrication nipples
Lubricate using an oil
can filled with uni-
versal oil.
3 lubrication nipples
4 lubrication nipples
14 lubrication nip-
ples.
14:A
14:B
14:C
14:D
Figure
15:A
15:B
15:C
15:D
15:E