Maintenance; Troubleshooting - sammic SA-3000 Gebrauchsanweisung

tial that the lamp remains on or cutlery
will not be sanitised properly and turned
off when replacing the polish granules or
carrying out any maintenance. Exposure
to the radiation of this lamp is harmful to
the eyes and skin. SAMMIC has implemen-
ted all the necessary precautionary mea-
sures; any improper use of the lamp is the
user's sole responsibility.
·Performance: Machine
depends on the weight of the items of
cutlery and the feeding rate.
SA-3000: 3000 to 4000 pieces/hour
SA-5000: 3500 to 5000 pieces/hour
Items of cutlery shall be fed gradually,
taking care that those previously introdu-
ced have disappeared into the granules
(from 5 to 10 pieces at a time).
Feeding rates:
SA-3000 13 pcs/every 15 seconds
SA-5000 14 pcs/every 10 seconds.
Check that the flow of items of cutlery
coming out through the outlet (B) is homo-
geneous and continuous.

MAINTENANCE

WARNING! Before cleaning or carrying out
maintenace of your dryer polisher, always
unplug it from the mains.
·Change of polish granules: Granules
must be changed when dirty or fine-grai-
ned. Due to the presence of water and
heat, the effectiveness of the granules is
reduced. Polish granules should be chan-
ged on a monthly basis, when working 4-
5 hours a day, and in any case at least
every 200 hours.
Procedure for changing the polish granu-
les: Remove used granules with a vacuum
cleaner. Then follow proceedure for filling
as previous.
· NOTE: If the power cable should get
damaged, it would be necessary to fit a
new one; such a replacement may be
done only by a SAMMIC authorised tech-
nical assistance service.
· Should you observe any malfunction,
then contact a SAMMIC authorised tech-
nical assistance service as soon as possi-
ble.
· Use wet cloth and mild detergent for cle-
aning. Never power clean.
throughput · Never clean the polycarbonate hopper
cover with solvents, alcohol, window-cle-
aning fluids or any abrasive materials,
since they may be harmful to the mecha-
nical properties of the cover.
ACCESSORIES
Machine supplied with start-up pack of
5kgs of polish granules.
For replacement contact your supplier.

TROUBLESHOOTING

·Cutlery discharge is not homogeneous
1. Motor direction of rotation is incorrect.
On three-phase motors, change the pola-
rity.
2. Cutlery jam. In this event: stop the
machine. Lift the top cover. Check for
jam in the upward path. If any, remove
the transparent cover after loosening the
fixing knobs. Clear the obstruction con-
cerned. Be careful when introducing
your hands, as there may be sharp
items. Replace the cover and fix it with
the rubber washers and knobs. The
transparent cover should not be left
loose, because this would lead to an
increase in noise and a possible fatigue
fracture of the cover.
·Polish granules flow out through the
cutlery outlet.
The machine holds 5kg of polish granu-
les. With the cutlery dampness, this pro-
duct may increase in volume.
·The dryer polisher will not start.
Check that:
the machine is connected and the power
switched on;
the top cover is closed;
the magnet switch in the top cover is in
good condition.
·The machine vibrates excessively.
Check that:
the machine stands firmly on the ground;
the wheels are in good condition;
the wheel brakes are locked.
·Not heating.
The safety thermostat has tripped due to a
malfunction of the heating unit. Call a
SAMMIC authorised technical assistance
service immediately.
· The germicidal UV-C lamp does not
light.
The lamp has burnt out or there is pro-
blem with the reactor-starter unit. Call a
SAMMIC authorised technical assistance
service immediately.
OTHER IMPORTANT INFORMATION
Sound level of the machine standing on a
firm ground and correctly braked is 72dB.
Background noise is 25dB. Measurement is
made at a height of 1.6m and 1m away
from the source.
ENGLISH 5