OCEAN S6 Technische Daten Betriebsspannung: über WimTec Netzteil 230 V 50 Hz / 12 V= Art.Nr. 117 899 - für eine Steuerung Art.Nr. 113 792 - für bis zu 5 Steuerungen Leistungsaufnahme: max. 3,5 W Magnetventil: Kartusche 6 V Ansprechbereich:...
Taste der Funktionen Anschluss für 12 V zum Entriegeln der 38 °C Spannungsversorgung Sicherheitssperre. Infrarot-Sensor für die Benutzererkennung (Ansprechbereich). Generell gilt für alle Regler: Gegen den Uhrzeiger- sinn zum Reduzieren. Im Uhrzeigersinn zum Erhöhen. WimTec OCEAN S6 Duschearmatur...
Infrarot-Sensors von 30-70 cm. selbstständig eine Spülung für Duschearmatur automatisch Automatische Reichweiten- 10 s aus, um die Rohrleitun- ab. Um bei einer unbeab- Adjustierung innerhalb der gen von Stagnationswasser sichtigten Daueraktivierung eingestellten Maximal- freizuspülen. Wasser zu sparen. Reichweite. WimTec OCEAN S6 Duschearmatur...
(bei Auslieferung geschlossen) Schmutzsieb und Rückfl ussverhinderer Fixierschraube zum Anschluss des Kabels für den Potentialausgleich Verdrahtungsschema für thermische Desinfektion WimTec OCEAN S6 - TD Steuerleitung nur für thermische Desinfektion Art.Nr. 112 108, 114 621 2 x 0,5 mm max. 100 m Gesamt-Kabellänge Schlüsselschalter...
Reihenfolge ausführen! Ggf. zwischen Wand und Rohbauset mit Silikon abdichten. Fotos beziehen sich auf 4. Wasserzuleitung absperren. Variante mit thermischer Desinfektion. Beide Vorabsperrungen mit einem Schraubendreher öffnen. Adapter für Thermostat mit Inbus 2,5 montieren. WimTec OCEAN S6 Duschearmatur...
Seite 8
Magnetventile erfolgt). Erdungskabel (gelb) an der Wasserstrecke befestigen. Montagerahmen mit 4 beiliegenden Schrauben befestigen. Dabei auf die Kabelverbindungen achten und die Kabel nicht quetschen. Beim Festziehen der Schrauben darauf achten, dass sich der Montagerahmen nicht verformt. WimTec OCEAN S6 Duschearmatur...
Seite 9
Anschlag drehen, dann nach rechts bis Pfeil nach oben zeigt). Position des Thermostatknopfes kontrollieren - Absperrknopf zeigt senkrecht nach oben. Glasplatte schräg aufsetzen und mit Druck in die waagrechte Position nach links drehen. Glasplatte mit Sicherungsschraube rechts unten sichern. WimTec OCEAN S6 Duschearmatur...
Seite 10
OFF Symbol wird der Wasserfluss gestartet. Während des Duschkabinen, kann eine Funktionstest die Hand im Nahbereich des Infrarotsensors Justierung der Reichweite belassen. Nach Verlassen des Ansprechbereichs schaltet der (s. S. 5) erforderlich sein. Wasserfluss automatisch ab. WimTec OCEAN S6 Duschearmatur...
3 4 5 6 beginnt langsam zu pulsieren. 30-70 cm AUSSCHALTEN: Touch-Tronic-Taste Automatik Antippen innerhalb des Dusche stoppt nach Ablauf ON/OFF Symbols schaltet der Nachlaufzeit wenn der die Dusche ab. Benutzer den Ansprechbereich verlässt oder nach Ablauf der Sicherheitsspülstopp-Zeit. WimTec OCEAN S6 Duschearmatur...
Seite 12
2 s ein. beginnt langsam zu pulsieren. 30-70 cm AUSSCHALTEN: Touch-Tronic-Taste Automatisch Dusche stoppt nach Ablauf Antippen innerhalb des der Nachlaufzeit, wenn der ON/OFF Symbols schaltet Benutzer den Ansprechbereich die Dusche ab. verlässt oder nach Ablauf der Sicherheitsspülstopp-Zeit. WimTec OCEAN S6 Duschearmatur...
Seite 13
Dusche ein. erkannt. Das Leuchtsymbol beginnt langsam zu pulsieren. 30-70 cm AUSSCHALTEN: Touch-Tronic-Taste Sicherheitsspülstopp Antippen innherhalb des Nach Ablauf der eingestellten ON/OFF Symbols schaltet Spülstopp-Zeit (siehe S. 5) die Dusche ab. schaltet die Dusche auto- matisch ab. WimTec OCEAN S6 Duschearmatur...
Tritt während dieser 30 s der 3 4 5 6 Dabei leuchtet beim ON/OFF Benutzer für mindestens 5 s in Symbol der senkrechte Strich den Ansprechbereich, geht die während der Ring pulsiert. Dusche in den Normalbetrieb über. 30-70 cm WimTec OCEAN S6 Duschearmatur...
Seite 15
Verbrühschutz aktiviert Während der thermischen Sollte sich eine Person Desinfektion überwacht der annähern, wird der Wasser- Infrarot-Sensor den Aktiv- fluss sofort gestoppt und bereich der Armatur. die thermische Desinfektion abgebrochen. Nur bei der Produktvariante mit thermischer Desinfektion. WimTec OCEAN S6 Duschearmatur...
Seite 16
2 min nach deren Deakti- für 10 s aus. vierung aus. 5 s vor und nach der Stagnationsfreispülung wird diese durch ein schnelles Blinken* der ON/OFF Symbolik signalisiert. 30-70 cm 3 - 48 h 10 s WimTec OCEAN S6 Duschearmatur...
Seite 17
Hand auf das Armatur nach einer Sicher- ON/OFF Symbol tippen und der heitszeit von 3 s wieder in den Reinigungsstopp ist aktiviert. Normalbetrieb über. Die Reinigungsstoppzeit dauert 10 Minuten ab Verlassen des Ansprechbereiches. 30-70 cm WimTec OCEAN S6 Duschearmatur...
OCEAN S6 General notes Congratulations on purchasing the WimTec OCEAN S6. In order to ensure that you will be able to enjoy this high-quality product for many years, please take note of the following cleaning and maintenance recommendations: Use mild cleaning agents containing soap...
Outlet rain shower Outlet rain shower R 1/2“ IG R 1/2“ IG Electr. installation Electr. installation pipe for 12 V= pipe for 12 V= R 1/2“ IG R 1/2“ IG R 1/2“ IG R 1/2“ IG WimTec OCEAN S6 Shower control...
Seite 22
Connection terminal for 12-V barriere power supply Infrared sensor for user detection (active range) The general rule applies to all controls: Move anticlockwise to decrease the setting. Move clockwise to increase the setting. WimTec OCEAN S6 Shower control...
Seite 23
After the configured maximum perform a 10-s rinse to flush Automatic range adjustment flow time has elapsed, the stagnant water from the within the preset maximum water stops automatically to pipes. range. prevent unintentional conti- nuous activation. WimTec OCEAN S6 Shower control...
Seite 24
Dirt fi lter and return fl ow valve Fixing screw for mounting of potential equalisation cable Wiring diagram for thermal disinfection WimTec OCEAN S6 - TD Control line only for thermal disinfection Art.No. 112 108, 114 621 2 x 0.5 mm total cable length max.
Seite 25
Where necessary, seal off space between wall and flush- The assembly photos refer mount set with silicone. to WimTec OCEAN with thermal disinfection. Close the main water valve. Open both integrated stop valves using a screwdriver.
Seite 26
Connect the magnetic valves to the electronics module. (no marking = rain shower, red = therm. disinfection) Feed the WimTec power cable 3m (with the electronics modu- le and connect it to the power supply . Then turn on the power supply.
Seite 27
Insert outlet pipe carefully through the glass plate and apply some pressure while turning it until it is aligned horizontally. Place the plastic spacer ring over the outlet pipe towards the front plate. WimTec OCEAN S6 Shower control...
Seite 28
Keap your hand in the active range during ment of the range (see the function test. After leaving the active range the water page 23) may be required. flow stops automatically. WimTec OCEAN S6 Shower control...
The water flow stops at the point (head or hand shower) end of the shut-off delay once to switch this off. the user leaves the sensor range or after the configured water arrest time has elapsed. WimTec OCEAN S6 Shower control...
Seite 30
The water flow stops at the Tap on the ON/OFF button to end of the shut-off delay once switch this off. the user leaves the sensor range or after the configured water arrest time has elapsed. WimTec OCEAN S6 Shower control...
Seite 31
30-70 cm SWITCH OFF: Touch-tronic button Safety flow arrest Tap on the ON/OFF button to After the configured water switch this off. arrest time (see p. 23) has elapsed, the shower will auto- matically shut off. WimTec OCEAN S6 Shower control...
Seite 32
If you enter the sensor range 3 4 5 6 while the ring pulsates. for at least 5 s during these 30 s, the shower will switch to normal operation. 30-70 cm WimTec OCEAN S6 Shower control...
Seite 33
The infrared sensor monitors If someone approaches the the sensor range of the fitting during thermal disinfection. sensor, the flow of water is immediately stopped and thermal disinfection is aborted. Only possible with models featuring thermal disinfection: WimTec OCEAN S6 Shower control...
Seite 34
2 min after it has been disabled. For 5 s before and after the stagnation rinse, the ON/OFF icon will flash rapidly. 30-70 cm 3 - 48 h 10 s WimTec OCEAN S6 Shower control...
Seite 35
The The fitting will resume normal cleaning stop remains enabled operation with a safety delay for 10 min after leaving the of 3 s after you leave the sensor range. sensor range. 30-70 cm WimTec OCEAN S6 Shower control...
Seite 37
Glass front plate white 115 673 Glass front plate black 115 536 Thermostat knob 113 877 Locking screw 117 899 Power supply (1-connect.) 113 792 Power supply (5-connect.) 113 167 Power supply cable 3 m WimTec OCEAN S6 Shower control...
Seite 38
OCEAN S6 WimTec OCEAN S6 Shower control...
Seite 39
OCEAN S6 WimTec OCEAN S6 Shower control...
Seite 40
WIMTEC Sanitärprodukte GmbH p: A - 3325 Ferschnitz, Freidegg 50, AUSTRIA t: +43 (0) 7473 5000 f: +43 (0) 7473 5000 - 500 m: verkauf@wimtec.com i: www.wimtec.com...